- 您現在的位置：買賣IC網 > PDF目錄369886 > LXT9883HC LAN HUB CONTROLLER PDF資料下載
參數資料
| 型號： | LXT9883HC |
| 英文描述： | LAN HUB CONTROLLER |
| 中文描述： | 局域網集線器控制器 |
| 文件頁數： | 32/96頁 |
| 文件大?。?/td> | 1309K |
| 代理商： | LXT9883HC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁
LXT980/980A Dual-Speed, 5-Port Fast Ethernet Repeater
32
Datasheet
internal register. The LEDs generally operate under hardware control although some limited
software overrides are available. In addition to On and Off states, some LED drivers provide a
blink state output.
2.3.1
Blink Rates
Two programmable blink rates are provided. The default period for the slow blink rate is 1.6s. The
default period is 0.4s for the fast blink rate. These rates may be changed via the LED Timer
Register. The slow blink rate is defined by the upper 8 bits and the fast blink rate is defined by the
lower 8 bits of the LED Timer Register. Refer to
Table 73
through
Table 75
for details.
2.3.2
Power-Up and Reset Conditions
During reset or power-up, all LED drivers turn on steady and remain on for approximately 2
seconds after reset is cleared. After reset, the Collision, Activity, and Redundant Power Supply
LEDs revert to hardware control. The Global Fault and Port LEDs revert to hardware control
unless a manager is present in the system.
2.3.3
Port LEDs
Port LEDs provide status for the four twisted-pair ports and the MII port. The LXT980 has 3 LED
driver pins for each port as described in
Table 8
. These pins drive standard LEDs. Three user-
selectable modes are provided for the port LEDs. Port LED states are also affected by port speed
and auto-negotiation status, see
Table 13
through
Table 15
.
2.3.3.1
Link Loss
During link loss, the Speed LED indicates10M, and the Partition LED indicates
“
No partition,
”
regardless of actual partition status.
2.3.3.2
Software Overrides of Port LEDs
The Port LED Control Register allows limited software overrides of the Port LEDs. Two bits per
port provide independent control of each port. However, all three LEDs for the respective port
receive the same override (all Port
n
LEDs will be simultaneously set to On, Off, or Blink). Refer
to
Table 69
and
Table 74
for coding and bit assignments.
2.3.4
Segment LEDs
These outputs can directly drive LEDs to indicate activity and collision status on a per segment
basis. No software overrides are provided for these LED drivers, and they are not affected by LED
mode selection. Pulse stretchers are used to extend the on-time for these LEDs.
2.3.4.1
Collision LEDs
The collision LEDs turn on for approximately 120
μ
s when the LXT980 detects a collision on the
respective 10 Mbps or 100 Mbps segment. During the time that the collision LED is on, any
additional collisions are ignored by the collision LED logic.
相關PDF資料 |
PDF描述 |
|---|---|
| LZ1030M | Common Anode Diode Array |
| LZ1032AD | Interface IC |
| LZ1032AM | Interface IC |
| LZ1032AR | Interface IC |
| LZ1132BD | Interface IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LXTON/H0 | 制造商:Red Lion Controls 功能描述:ANNUN LABELS, 1 LPAX LABEL: TON/H 制造商:Red Lion Controls 功能描述:1 LPAX LABEL TON/H |
| LXTON000 | 制造商:Red Lion Controls 功能描述:ANNUNCIATOR LABELS,1 LPAX LABEL: TON 制造商:Red Lion Controls 功能描述:1 LPAX LABEL TON |
| LXU/MIN0 | 制造商:Red Lion Controls 功能描述:ANNUN LABELS, 1 LPAX LABEL: U/MIN 制造商:Red Lion Controls 功能描述:1 LPAX LABEL U/MIN |
| LXUA0000 | 制造商:Red Lion Controls 功能描述:ANNUNCIATOR LABELS, 1 LPAX LABEL: UA 制造商:Red Lion Controls 功能描述:1 LPAX LABEL UA |
| LXV00000 | 制造商:Red Lion Controls 功能描述:ANNUNCIATOR LABELS, 1 LPAX LABEL: V 制造商:Red Lion Controls 功能描述:1 LPAX LABEL V |
發布緊急采購，3分鐘左右您將得到回復。