- 您現在的位置：買賣IC網 > PDF目錄369886 > LXT9761HC LAN TRANSCEIVER|HEX|QFP|208PIN|PLASTIC PDF資料下載
參數資料
| 型號： | LXT9761HC |
| 英文描述： | LAN TRANSCEIVER|HEX|QFP|208PIN|PLASTIC |
| 中文描述： | 網絡收發器|六角| QFP封裝| 208PIN |塑料 |
| 文件頁數： | 61/68頁 |
| 文件大?。?/td> | 1177K |
| 代理商： | LXT9761HC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁當前第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
Low-Power Octal PHY
—
LXT9784
Datasheet
61
0.9
Restart Auto-
Negotiation
Restarts the auto-negotiation process and is self cleared after 300 ns
1 = Restart auto-negotiation process.
default 0 = normal operation.
RW
SC
0.8
Duplex Mode
Controls the duplex mode when auto-negotiation is disabled. If the PHY reports that
it only able to operate in one duplex mode (via bits 1.15:11), the value of this bit shall
correspond to the mode which the PHY can operate.
When the PHY is placed in Loopback mode, the behavior of the PHY shall not be
affected by the status of this bit, bit 0.8.
1 = Full Duplex.
default 0 = Half Duplex.
RW
0.7
Collision Test
Force collision in response to the assertion of TXEN.
1 = Force COL.
default 0 = disable Collision signal test.
RW
0.6:0
Reserved
Constant
“
0
”
.
RO
Table 44. Status Register (Register 1) Bit Definitions
Bit(s)
Name
Description
Type
1
1.15
100BASE-T4
Constant 0 = PHY not able to perform 100BASE-T4.
RO
1.14
Reserved
Constant
“
0
”
.
RO
1.13
100BASE-TX Half
Duplex
1 = PHY able to perform half duplex 100BASE-TX
0 = PHY not able to operate in 100BASE-TX
RO
1.12
Reserved
Constant
“
0
”
.
RO
1.11
10 Mbps Half Duplex
1 = PHY able to operate at 10 Mbps in half duplex mode
0 = PHY not able to operate in 10BASE-T
RO
1.10:7
Reserved
Constant
“
0
”
.
RO
1.6
MF Preamble
Suppression
Constant 0 = PHY will not accept management frames with preamble
suppressed.
RO
1.5
Auto-Negotiation
Complete
1 = Auto-Negotiation process completed
default 0 = Auto-Negotiation process has not completed.
RO
1.4
Remote Fault
Constant 0 = no remote fault condition detected
RO
1.3
Reserved
Constant 0
RO
1.2
Link Status
1 = Valid link has been established.
default 0 = Invalid link detected.
RO
LL
SC
1.1
Jabber Detect
This bit has meaning only in 10 Mbps mode.
1 = Jabber condition detected.
default 0 = No jabber condition detected.
RO
LH
SC
1.0
Extended Capability
Constant 1 = Extended register capabilities enabled
RO
1. Refer to
Table 42
for Type definitions.
Table 43. Control Register (Register 0) Bit Definitions (Continued)
Bit(s)
Name
Description
Type
1
1. Refer to
Table 42
for Type definitions.
相關PDF資料 |
PDF描述 |
|---|---|
| LXT9762 | Interface IC |
| LXT9762HC | LAN TRANSCEIVER|HEX|QFP|208PIN|PLASTIC |
| LXT9781 | Interface IC |
| LXT9781BC | LAN TRANSCEIVER|OCTAL|BGA|272PIN|PLASTIC |
| LXT9781HC | LAN TRANSCEIVER|OCTAL|QFP|208PIN|PLASTIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LXT9762 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Fast Ethernet 10/100 Multi-Port Transceiver with Serial MII |
| LXT9762HC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN TRANSCEIVER|HEX|QFP|208PIN|PLASTIC |
| LXT9763 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Fast Ethernet 10/100 Hex Transceiver with Full MII |
| LXT9763HC | 制造商:LEVEL_ONE 功能描述: |
| LXT9763HC-B2 | 制造商:Intel 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。