- 您現在的位置：買賣IC網 > PDF目錄369886 > LXT971ABC LAN TRANSCEIVER|SINGLE|CMOS|BGA|64PIN|PLASTIC PDF資料下載
參數資料
| 型號： | LXT971ABC |
| 英文描述： | LAN TRANSCEIVER|SINGLE|CMOS|BGA|64PIN|PLASTIC |
| 中文描述： | 網絡收發器|單|的CMOS | BGA封裝| 64管腳|塑料 |
| 文件頁數： | 60/68頁 |
| 文件大?。?/td> | 1177K |
| 代理商： | LXT971ABC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁當前第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
LXT9784
—
Low-Power Octal PHY
60
Datasheet
5.0
Register Definitions
The PHY registers can be accessed through the MII management interface.
Table 42
defines the bit type designations used in the following tables.
Table 42. Bit Type Designations
Designator
Definition
SC
Self Cleared
RO
Read Only
P
external Pin affects content
LL
Latch Low
LH
Latch High.
Table 43. Control Register (Register 0) Bit Definitions
Bit(s)
Name
Description
Type
1
0.15
Reset
Sets the status and control register of the PHY to their default states and is self-
clearing. The PHY returns a value of
“
1
”
when this register is read until the reset
process has completed and accepts a read or write transaction.
1 = PHY reset.
default 0 = normal operation.
RW
SC
0.14
Loopback
Enable loopback of transmit data to the receive data path. The PHY receive circuitry
is isolated from the network.
Note that this may cause the de-scrambler to lose synchronization and produce 560
ns of
“
dead time
”
.
1 = Loopback enabled.
default 0 = Loopback disabled (normal operation).
RW
0.13
Speed Selection
Controls speed when auto-negotiation is disabled.
default 1 = 100 MBPS
0 = 10 MBPS
RW
P
0.12
Auto-Negotiation
Enable
Bits 0.13 & 0.8 (Speed Selection and Duplex Mode, respectively) are ignored when
auto-negotiation is enabled.
Bits 4.12:5 (Technology Ability Field) depends on the PHY ability (Register 0) to
define the preferred link configuration.
default 1 = auto-negotiation enable.
0 = auto-negotiation disable.
RW
P
0.11
Power Down
1 = Analog section
only
power-down enabled.
default 0 = Power-down disabled (normal operation).
RW
0.10
Isolate
Allows the PHY to isolate the Media Independent Interface. The PHY doesn't
respond on the both transmit and receive activities.
1 = Logical isolate of internal MII interface.
default 0 = Normal operation.
RW
1. Refer to
Table 42
for Type definitions.
相關PDF資料 |
PDF描述 |
|---|---|
| LXT971ABE | LAN TRANSCEIVER|SINGLE|CMOS|BGA|64PIN|PLASTIC |
| LXT971ALC | LAN TRANSCEIVER|SINGLE|CMOS|QFP|64PIN|PLASTIC |
| LXT971ALE | LAN TRANSCEIVER|SINGLE|CMOS|QFP|64PIN|PLASTIC |
| LXT974QC | LAN Transceiver |
| LXT975QC | LAN Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LXT971ABE | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:3.3V Dual-Speed Fast Ethernet PHY Transceiver |
| LXT971ALC | 制造商:Intel 功能描述:LAN Transceiver, Single, 64 Pin, Plastic, QFP 制造商:Intellon Corporation 功能描述:LAN Transceiver, Single, 64 Pin, Plastic, QFP 制造商:Level One 功能描述:LAN Transceiver, Single, 64 Pin, Plastic, QFP |
| LXT971ALE | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:3.3V Dual-Speed Fast Ethernet PHY Transceiver |
| LXT971LC | 制造商:Intel 功能描述: |
| LXT972A | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:3.3V Dual-Speed Fast Ethernet Transceiver Datasheet |
發布緊急采購，3分鐘左右您將得到回復。