參數資料
型號： LXT914QE
英文描述： LAN Transceiver
中文描述： 網絡收發器
文件頁數： 10/42頁
文件大?。?/td> 561K
代理商： LXT914QE
LXT914
—
Flexible Quad Ethernet Repeater
10
Datasheet
Table 2. LXT914 Inter-Repeater Backplane Signal Descriptions
PLCC
PQFP
Symbol
I/O
Description
4
94
IRENA
I/O
Inter-Repeater Backplane Enable.
This pin allows individual LXT914
repeaters to take control of the Inter-Repeater Backplane (IRB) data bus
(IRDAT). The IRENA bus must be pulled up locally by a 330
resistor.
1
5
95
IRDAT
I/O
IRB Data.
This pin is used to pass data between multiple repeaters on the
IRB. The IRDAT bus must be pulled up locally by a 330
resistor.
1
6
96
IRDEN
O
IRB Driver Enable.
The IRDEN pin is used to enable external bus drivers
which may be required in synchronous systems with large backplanes. This
is an active Low signal, maintained for the duration of the data
transmission. IRDEN must be pulled up locally by a 330
resistor.
7
8
97
98
IRCFS
IRCOL
I/O
I/O
IRB Collision Flag Sense
(IRCFS) and
IRB Collision
(IRCOL). These two
pins are used for collision signalling between multiple LXT914 devices on
the Inter-Repeater Backplane (IRB). Both the IRCFS bus and the IRCOL
bus must be pulled up globally with 330
resistors. (IRCFS requires a
precision resistor [±1%].)
NOTES:
1. IRENA and IRDAT can be buffered between boards in multi-board configurations. Where buffering is used,
a 330
pull-up resistor can be used on each signal, on each board. Where no buffering is used, the total
impedance should be no less than 330
.
2. IRCFS and IRCOL cannot be buffered. In multi-board configurations, the total impedance on IRCOL should
be no smaller than 330
. IRCFS should be pulled up only once, by a single 330
, 1% resistor.
Table 3. LXT914 Mode Select and Control Signal Descriptions
PLCC
PQFP
Symbol
I/O
Description
12
8
A/SYNC
I
Backplane Sync Mode Select.
This pin selects the backplane sync mode.
When this pin is left floating an internal pull-up defaults to the
Asynchronous mode (A/SYNC High). In the asynchronous mode 12 or
more LXT914s can be connected on the backplane, and an external 10
MHz backplane clock source is not required. When the synchronous mode
is selected (A/SYNC tied Low), 32 or more LXT914s can be connected to
the backplane and an external 10 MHz backplane clock source is required.
13
9
LOC/EXT
I
Management Mode Select.
This pin selects the management mode. When
this pin is left floating, an internal pull-up defaults to the Local management
mode (LOC/EXT High). In the Local mode, setup parameters are
downloaded from an EEPROM during initialization. Once initialized with the
setup parameters, the repeater functions independently.
28
33
LEDJM/
AUISEL
I/O
LED Driver or DTE/MAU Select.
At reset, this pin selects the mode of the
AUI port. If left floating, an internal pull-down device forces the AUI port to
DTE mode. If pulled High with an external resistor, the port changes to a
MAU, in which case the functions of the LEDJM pin are disabled and the
default LED mode (Refer to
Table 7
) is not available.
—
30
AUISEL
I
DTE/MAU Select.
This pin changes the mode of the AUI port independent
of the condition at reset. This function is available only in the 100-pin PQFP
package.
17
35
14
40
LEDM0
LEDM1
I/O
I/O
LED Mode 0 & 1 Select.
These two pins select one of four possible LED
modes of operation. The Functional Description section describes the four
modes.
相關PDF資料
PDF描述
LXT916QC LAN Transceiver
LXT917QC LAN Transceiver
LXT9784BC LAN TRANSCEIVER|OCTAL|BGA|324PIN|PLASTIC
LXT9784BE LAN TRANSCEIVER|OCTAL|BGA|324PIN|PLASTIC
LXT9785BC LAN TRANSCEIVER|OCTAL|BGA|241PIN|PLASTIC
相關代理商/技術參數
參數描述
LXT915 制造商:LVL1 制造商全稱:LVL1 功能描述:Simple Quad Ethernet Repeater
LXT915QC 制造商:LEVEL ONE 功能描述:LAN HUB CONTROLLER, 64 Pin, QFP
LXT916 制造商:LVL1 制造商全稱:LVL1 功能描述:Multi-Port Hub Repeaters for Managed 10BASE-T Applications
LXT916QC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN Transceiver
LXT917 制造商:LVL1 制造商全稱:LVL1 功能描述:Multi-Port Hub Repeaters for Managed 10BASE-T Applications
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*