- 您現在的位置：買賣IC網 > PDF目錄369886 > LXT914PE LAN HUB CONTROLLER PDF資料下載
參數資料
| 型號： | LXT914PE |
| 英文描述： | LAN HUB CONTROLLER |
| 中文描述： | 局域網集線器控制器 |
| 文件頁數： | 28/42頁 |
| 文件大?。?/td> | 561K |
| 代理商： | LXT914PE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
LXT914
—
Flexible Quad Ethernet Repeater
28
Datasheet
3.0
Application Information
3.1
12-Port Hub Repeater
Figure 6
(Sheets 1 through 4) shows a simple 12-port hub repeater application with 3 LXT914s.
This application also provides two additional AUI ports
—
one DB-15 connector and one coaxial
port. The application shown uses the asynchronous backplane mode so no external backplane clock
source is required.
Figure 6
(Sheet 1) shows the XL93C46 EEPROM which downloads the setup parameters for all
the LXT914 devices at initialization. (This EEPROM could be replaced with a simple pull down
resistor on the SDI pin. This will select the default conditions of the set up register.) A single 20
MHz crystal provides the SYSCLK for all three LXT914 chips. The LXT914 hub repeater on Sheet
1 provides the AUI DB-15 connector as well as four twisted-pair ports.
Table 19
lists transformers
suggested for use with the LXT914.
Figure 6
(Sheet 2) shows a second LXT914 hub repeater with four TP ports and a coaxial port. The
MD-001 coax transceiver is used to implement the port. Sheet 3 shows the third LXT914 device
with its four TP ports and indicator LEDs. The AUI port of the third LXT914 hub repeater is not
used. Sheet 4 of the schematic shows the LEDs for the remaining LXT914 devices, along with the
LED operation table.
3.2
8-Port Print or File Server
Figure 7
(Sheets 1 and 2) shows an eight-port repeater attachment for an existing single port AUI
or 10BASE5 interface. This application can be added to a current design with an existing AUI or
10BASE5 interface. This circuit allows increased connectivity without the need for another
external remote hub. The application shown is a 68-pin PLCC, an asynchronous backplane with
both LXT914s in the first position.
In
Figure 7
(Sheet 1) the LXT914 is set up with the LEDs in Mode 1 with one LED per port and a
single collision LED. The twisted pair port LEDs display link integrity only. (Refer to
Table 16
.)
LED Mode 1 is selected by pulling LEDM0 High with a 1 k
resistor on pin 17 and pulling
LEDM1 Low with pin 35 attached to ground.
Figure 7
(Sheet 2) has the same configuration, mode of operation and LED Mode as used in Sheet
1. However, the AUI port has been configured as a MAU interface. This is selected when LEDJM/
AUISEL on pin 28 is pulled up through a 1 k
resistor. This mode disables the LEDJM pin as an
LED driver. (See
Table 13
.) The MAU interface now configured on the LXT914 allows the AUI
port to attach to a DTE interface. This application increases connectivity to any existing single-port
Ethernet design. This unique application allows the designer to integrate an external hub,
eliminating the need for additional external equipment.
相關PDF資料 |
PDF描述 |
|---|---|
| LXT914QE | LAN Transceiver |
| LXT916QC | LAN Transceiver |
| LXT917QC | LAN Transceiver |
| LXT9784BC | LAN TRANSCEIVER|OCTAL|BGA|324PIN|PLASTIC |
| LXT9784BE | LAN TRANSCEIVER|OCTAL|BGA|324PIN|PLASTIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LXT914QC | 制造商:LEVEL ONE 功能描述: |
| LXT914QE | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN Transceiver |
| LXT915 | 制造商:LVL1 制造商全稱:LVL1 功能描述:Simple Quad Ethernet Repeater |
| LXT915QC | 制造商:LEVEL ONE 功能描述:LAN HUB CONTROLLER, 64 Pin, QFP |
| LXT916 | 制造商:LVL1 制造商全稱:LVL1 功能描述:Multi-Port Hub Repeaters for Managed 10BASE-T Applications |
發布緊急采購，3分鐘左右您將得到回復。