- 您現在的位置：買賣IC網 > PDF目錄377789 > LX2206ILD (MICROSEMI CORP-ANALOG MIXED SIGNAL GROUP) Dual Level Lithium Ion Battery Charger PDF資料下載
參數資料
| 型號： | LX2206ILD |
| 廠商： | MICROSEMI CORP-ANALOG MIXED SIGNAL GROUP |
| 元件分類： | 電源管理 |
| 英文描述： | Dual Level Lithium Ion Battery Charger |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| 封裝： | ROHS COMPLIANT, PLASTIC, MLP-10 |
| 文件頁數： | 8/14頁 |
| 文件大?。?/td> | 311K |
| 代理商： | LX2206ILD |
LX2206
P
RODUCTION
D
ATA
S
HEET
Microsemi
Integrated Products Division
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 8
Copyright
2005
Rev. 1.2, 2006-12-22
W
M
.
C
Dual Level Lithium Ion Battery Charger
TM
A P P L I C A T I O N N O T E
L
AYOUT
In the layout of the Printed Circuit Board (PCB) it is
important to provide a solid path from the IC power and
ground pins to the power and ground planes of the PCB to
provide a good conduction path for heat. This insures the
LX2206 stays cool and can provide the maximum charge
current to minimize the time required to charge the battery.
For stability purposes and to reduce voltage switching
transients it is important to place capacitors close to the IN
and BAT pins. A 10μF capacitor (X5R or X7R dielectric)
is recommended.
C
URRENT
P
ROGRAMMING
R
ESISTORS
The LX2206 has two programming resistors to control
the battery charging current during the constant current
charging mode of the battery charging cycle. When the
H/L pin is high (selecting the High Current charging mode),
the charge current is determined by the value of the HCP
programming resistor. The maximum charge current is
determined by the programming current at either the HCP
or LCP programming pins (depending on the state of H/L);
the range of each of these channels is identical. The
programming current is the HCP or LCP pin voltage
(typically 1.25V) divided by the value of the programming
resistor. For example, the HCP current with a 110K resistor
to GND is:
1.25
I
HCP
11.4μA
110k
1.25
R
HCP
=
=
=
Charge Current vs IHCP (or ILCP)
0
200
400
600
800
1000
1200
0.00
50.00
100.00
150.00
IHCP (in uA)
C
Using the table below it can be seen that for a
programming current value of 11.4μA, the corresponding
maximum charge current is 92mA.
The termination current determines the point at which
the charge cycle is terminated and the battery is determined
to be fully charged. The termination current is determined
by the value of the HCP programming current as
determined by the HCP programming resistor. For a value
of IHCP = 11.4μA (as was used in the previous example),
the termination current from the chart below can be seen to
be 9mA.
Termination Current vs IHCP
0
20
40
60
80
100
120
0.00
50.00
100.00
150.00
IHCP (in uA)
T
The termination current is always roughly 10% of the
maximum charge current set by the HCP resistor.
A
P
P
L
I
C
A
T
I
O
N
S
相關PDF資料 |
PDF描述 |
|---|---|
| LX2207 | Three Level Lithium Ion Battery Charger |
| LX2207ILD | Three Level Lithium Ion Battery Charger |
| LX24T3 | Linear Excimer Lamp |
| LX401 | SILICON GATE ENHANCEMENT MODE RF POWER LDMOS TRANSISTOR |
| LX5107CDWT | Terminator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LX2206ILD-TR | 功能描述:IC CHARGER BATT DUAL LI-ON 10MLP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
| LX2207 | 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:Three Level Lithium Ion Battery Charger |
| LX2207 EVAL KIT | 制造商:Microsemi Corporation 功能描述:LINEAR - LITHIUM ION - Bulk |
| LX2207_0710 | 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:Three Level Lithium Ion Battery Charger |
| LX2207ILD | 制造商:Microsemi Corporation 功能描述:LINEAR - LITHIUM ION - Bulk |
發布緊急采購，3分鐘左右您將得到回復。