- 您現在的位置：買賣IC網 > PDF目錄377788 > LX1992 (Microsemi Corporation) High Efficiency LED Driver PDF資料下載
參數資料
| 型號： | LX1992 |
| 廠商： | Microsemi Corporation |
| 英文描述： | High Efficiency LED Driver |
| 中文描述： | 高效率LED驅動器 |
| 文件頁數： | 7/11頁 |
| 文件大?。?/td> | 335K |
| 代理商： | LX1992 |
Microsemi
Linfinity Microelectronics Division
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 7
Copyright
2000
Rev. 1.1b, 2005-03-03
W
M
.
C
LX1992
High Efficiency LED Driver
P
RODUCTION
D
ATA
S
HEET
TM
A P P L I C A T I O N I N F O R M A T I O N
( C O N T I N U E D )
Figure 5:
LXE1992 Engineering Evaluation Board
Table 1: Input and Ouput Pin Assignments
Pin Name
Allowable Range
Description
VBAT
0 to 6V
Main power supply for output. (Set external current limit to 0.5A)
LX1992 power. May be strapped to VBAT or use a separate supply if VCC jumper is in
the SEP position. Do not power output from VCC pin on board..
Potentiometer power. May be strapped to VBAT or use a separate supply if VPOT
jumper is in the SEP position. Do not power output from VPOT pin on board.
Apply a DC voltage or a PWM voltage to this pin to adjust the LED current. PWM
inputs should be greater than 120Hz and DC portion less than 350mV.
Pulled up to VCC on board (10K
), Ground to inhibit the LX1992.
VCC
1.6V to 6V
VPOT
1.6V to 6V
VADJ IN
0 to 350mV
/SHDN
0 to VCC
VOUT
0 to 18V
Power supply output voltage that is applied to LED string.
VFDBK
0 to 400mv
Sense resistor voltage. Divide this voltage by 15 to determine LED current.
Table 2: Jumper Pin Position Assignments
Jumper Position
Functional Description
VCC/ BAT
Use this position when powering VBAT and VCC from the same supply. Do not connect power to the VCC
input when using this jumper position.
VCC/ SEP
Use this position when using a separate VCC supply (different from VBAT).
VPOT/ VBAT
Use this position when powering the potentiometer reference circuit from the VBAT supply. Do not connect
power to the VCC input when using this jumper position.
Use this position when using a separate power supply (different from VBAT) to power the potentiometer
reference circuit. This will lower the VBAT current and provide a more accurate efficiency reading for the
LX1992 circuit.
VPOT/ SEP
ADJ/ POT
Use this position when using the potentiometer to adjust LED current.
ADJ/ EXT
Use this position when adjusting the LED current with an external PWM that has a repetition rate >120Hz. Or
when using a DC adjustment voltage.
Note: Always put jumpers in one of the two possible positions
A
P
P
L
I
C
A
T
I
O
N
相關PDF資料 |
PDF描述 |
|---|---|
| LX1992CDU | High Efficiency LED Driver |
| LX1992CLM | High Efficiency LED Driver |
| LX2202 | 2A Li-Ion Linear Charger and Power Control |
| LX2202CLQ | 2A Li-Ion Linear Charger and Power Control |
| LX2203A | Li-Ion Battery Charger |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LX1992-01EVALKIT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LED Driver |
| LX1992-02EVALKIT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LED Driver |
| LX1992-02W EVAL KIT | 制造商:Microsemi Corporation 功能描述:LX1992-02W EVAL KIT - Bulk |
| LX1992-03W EVAL KIT | 制造商:Microsemi Corporation 功能描述:LED BACKLIGHT CONTROLLERS AND DRIVERS - Bulk |
| LX1992CDU | 制造商:Microsemi Corporation 功能描述:LED DRVR 4Segment 1.8V/2.5V/3.3V/5V 8-Pin MSOP 制造商:Microsemi Corporation 功能描述:LED DRVR 4SEGMENT 1.6V TO 6V 8MSOP - Bulk |
發布緊急采購，3分鐘左右您將得到回復。