參數資料
型號: LTNS
廠商: Linear Technology Corporation
英文描述: 24-Bit No Latency ADC with Differential Input and Reference in MSOP
中文描述: 24位不具有差動輸入和ADC的參考延遲,采用MSOP
文件頁數: 35/40頁
文件大?。?/td> 503K
代理商: LTNS
LTC2411/LTC2411-1
35
Figure 42. Bridge Amplification Using a Single Amplifier
APPLICATIOU
Note that this 4-amplifier topology has advantages over
the typical integrated 3-amplifier instrumentation ampli-
fier in that it does not have the high noise level common in
the output stage that usually dominates when an instru-
mentation amplifier is used at low gain. If this amplifier is
used at a gain of 10, the gain error is only 10ppm and input
referred noise is reduced to 0.15
μ
V
RMS
. The buffer stages
can also be configured to provide gain of up to 50 with high
gain stability and linearity.
Figure 42 shows an example of a single amplifier used to
produce single-ended gain. This topology is best used in
applications where the gain setting resistor can be made
to match the temperature coefficient of the strain gauges.
If the bridge is composed of precision resistors, with only
one or two variable elements, the reference arm of the
bridge can be made to act in conjunction with the feedback
resistor to determine the gain. If the feedback resistor is
incorporated into the design of the load cell, using resis-
tors which match the temperature coefficient of the load-
cell elements, good results can be achieved without the
need for resistors with a high degree of absolute accuracy.
The common mode voltage in this case, is again a function
of the bridge output. Differential gain as used with a 350
bridge is:
R
R
R
1 175
W
U
U
A
V
=
=
+
9 95
.
1
2
Common mode gain is half the differential gain. The
maximum differential signal that can be used is 1/4 V
REF
,
as opposed to 1/2 V
REF
in the 2-amplifier topology above.
Remote Half Bridge Interface
As opposed to full bridge applications, typical half bridge
applications must contend with nonlinearity in the bridge
output, as signal swing is often much greater. Applications
include RTD’s, thermistors and other resistive elements
that undergo significant changes over their span. For
single variable element bridges, the nonlinearity of the half
Figure 43. Remote Half Bridge Interface
0.1
μ
F
5V
REF
+
REF
IN
+
IN
GND
V
CC
2
3
2
4
6
7
3
350
BRIDGE
4
5
2411 F42
6
1
+
LTC1050S8
5V
0.1
μ
V
R2
46.4k
20k
20k
175
1
μ
F
10
μ
F
R1
4.99k
A
V
= 9.95 =
R1 + R2
R1 + 175
+
+
1
μ
F
+
LTC2411/
LTC2411-1
2411 F43
REF
IN
+
IN
GND
V
CC
V
S
2.7V TO 5.5V
2
3
4
5
PLATINUM
100
RTD
R1
25.5k
0.1%
6
1
4
3
2
1
REF
+
LTC2411/
LTC2411-1
相關PDF資料
PDF描述
LTNT 24-Bit No Latency ADC with Differential Input and Reference in MSOP
LTWV 24-Bit No Latency ADC with Differential Input and Reference in MSOP
LTZ1000ACH Ultra Precision Reference
LTZ1000CH Ultra Precision Reference
LUDZS4.3B Low Current Operation at 250??A???Low Reverse Leakage,Low Noise Zener Diode(250??A?·¥?????μ?μ?????°????????????μ?μ?????????a?£°???é???o3?o???????)
相關代理商/技術參數
參數描述
LTNT 制造商:LINER 制造商全稱:Linear Technology 功能描述:24-Bit No Latency ADC with Differential Input and Reference in MSOP
LTO-01T-110N 制造商:JST Manufacturing 功能描述:Crimping Tools, Hand Tools 制造商:Pentair Technical Products / Hoffman 功能描述:TERMINAL FEMALE DISCONNECT 0.11IN CRIMP 制造商:HOFFMAN PRODUCTS 功能描述:TERMINAL, FEMALE DISCONNECT 0.11IN CRIMP 制造商:Pentair Technical Products / Hoffman 功能描述:TERMINAL, FEMALE DISCONNECT 0.11IN CRIMP; Connector Type:Female Disconnect; Series:-; Termination Method:Crimp; Stud/Tab Size:0.11" x 0.02"; Wire Size AWG Min:24AWG; Wire Size AWG Max:20AWG; Insulator Material:Uninsulated
LTO-01T-187N 制造商:JST Manufacturing 功能描述:
LTO030F10000FTE3 功能描述:厚膜電阻器 - 透孔 1K OHM 1% 30W RoHS:否 制造商:Caddock 電阻:27 kOhms 容差:1 % 功率額定值:8 W 溫度系數:50 PPM / C 系列:MS 端接類型:Axial 電壓額定值:2 kV 工作溫度范圍:- 15 C to + 275 C 尺寸:8.89 mm Dia. x 23.11 mm L 封裝:Bulk
LTO030F10000JTE3 功能描述:厚膜電阻器 - 透孔 1000ohms 5% RoHS:否 制造商:Caddock 電阻:27 kOhms 容差:1 % 功率額定值:8 W 溫度系數:50 PPM / C 系列:MS 端接類型:Axial 電壓額定值:2 kV 工作溫度范圍:- 15 C to + 275 C 尺寸:8.89 mm Dia. x 23.11 mm L 封裝:Bulk