- 您現在的位置：買賣IC網 > PDF目錄45000 > LTM8062EV#PBF (LINEAR TECHNOLOGY CORP) BATTERY CHARGE CONTROLLER, 1150 kHz SWITCHING FREQ-MAX, PBGA77 PDF資料下載
參數資料
| 型號： | LTM8062EV#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | BATTERY CHARGE CONTROLLER, 1150 kHz SWITCHING FREQ-MAX, PBGA77 |
| 封裝： | 15 X 9 MM, 4.32 MM HEIGHT, ROHS COMPLIANT, MO-222, LGA-77 |
| 文件頁數： | 9/24頁 |
| 文件大小： | 580K |
| 代理商： | LTM8062EV#PBF |
LTM8062/LTM8062A
17
8062fa
APPLICATIONS INFORMATION
1. Place the CIN capacitor as close as possible to the VIN
and GND connection of the LTM8062/LTM8062A.
2. If used, place the CBAT capacitor as close as possible to
theBATandGNDconnectionoftheLTM8062/LTM8062A.
3. PlacetheCINandCBAT(ifused)capacitorssuchthattheir
ground current flows directly adjacent or underneath
the LTM8062/LTM8062A.
4. Connect all of the GND connections to as large a copper
pour or plane area as possible on the top layer. Avoid
breaking the ground connection between the external
components and the LTM8062/LTM8062A.
5. For good heat sinking, use vias to connect the GND
copper area to the board’s internal ground planes.
Liberally distribute these GND vias to provide both a
goodgroundconnectionandthermalpathtotheinternal
planes of the printed circuit board. Pay attention to the
location and density of the thermal vias in Figure 5. The
LTM8062/LTM8062A can benefit from the heat-sinking
afforded by vias that connect to internal GND planes at
these locations, due to their proximity to internal power
handlingcomponents.Theoptimumnumberofthermal
vias depends upon the printed circuit board design.
For example, a board might use very small via holes.
It should employ more thermal vias than a board that
uses larger holes.
Hot-Plugging Safely
The small size, robustness and low impedance of ceramic
capacitors make them an attractive option for the input
bypass capacitor of LTM8062/LTM8062A. However, these
capacitors can cause problems if the LTM8062/LTM8062A
are plugged into a live input supply (see Application Note
88 for a complete discussion). The low loss ceramic
capacitor combined with stray inductance in series with
the power source forms an underdamped tank circuit,
and the voltage at the VIN pin of the LTM8062/LTM8062A
can ring to more than twice the nominal input voltage,
possibly exceeding the LTM8062/LTM8062A’s rating and
damage the part. If the input supply is poorly controlled
or the user will be plugging the LTM8062/LTM8062A into
anenergizedsupply,theinputnetworkshouldbedesigned
to prevent this overshoot. This can be accomplished by
installing a small resistor in series with VIN, but the most
popular method of controlling input voltage overshoot is
to add an electrolytic bulk capacitor to the VIN net. This
capacitor’s relatively high equivalent series resistance
damps the circuit and eliminates the voltage overshoot.
The extra capacitor improves low frequency ripple filter-
ing and can slightly improve the efficiency of the circuit,
though it is physically large.
Parallel Operation
If more current is desired, multiple LTM8062/LTM8062As
may be paralleled, as shown in the Typical Applications
section. When doing so, bear in mind the following:
1. Each LTM8062/LTM8062A ADJ pin requires 250k input
resistance as described in the ADJ pin function descrip-
tion. Table 1 gives the recommended resistor network
for a single LTM8062/LTM8062A. If using more than
one, either apply one network of the appropriate value
to each LTM8062/LTM8062A’s ADJ pin or apply a single
network, each resistor value divided by the number of
paralleled LTM8062/LTM8062As and connect all of the
ADJ pins together.
2. Tie the BAT outputs directly together. Apply the same
output capacitance to each LTM8062/LTM8062A as if
it were used as a single device and not paralleled.
3. The individual LTM8062/LTM8062As may not share
current equally as the battery nears the float voltage.
Thermal Considerations
The thermal performance of the LTM8062/LTM8062A is
given in the Typical Performance Characteristics section.
These curves were generated by the LTM8062/LTM8062A
mounted to a 58cm2 4-layer FR4 printed circuit board.
Boards of other sizes and layer count can exhibit differ-
ent thermal behavior, so it is incumbent upon the user to
verify proper operation over the intended system’s line,
load and environmental operating conditions.
Forincreasedaccuracyandfidelitytotheactualapplication,
many designers use FEA to predict thermal performance.
To that end, the Pin Configuration section of the data sheet
typically gives four thermal coefficients:
相關PDF資料 |
PDF描述 |
|---|---|
| LTM8062AEV#PBF | BATTERY CHARGE CONTROLLER, 1150 kHz SWITCHING FREQ-MAX, PBGA77 |
| LTM9005CV-AA#PBF | SPECIALTY ANALOG CIRCUIT, PBGA204 |
| LTM9005CV-AB#PBF | SPECIALTY ANALOG CIRCUIT, PBGA204 |
| LTM9005IV-AB#PBF | SPECIALTY ANALOG CIRCUIT, PBGA204 |
| LUCW3000ACN-TR | PLL FREQUENCY SYNTHESIZER, 2200 MHz, PDSO14 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTM8062IV#PBF | 功能描述:IC BATTERY CHARGER TRACK 77-LGA RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:µModule® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| LTM8062IVPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:32VIN, 2A μModule Power Tracking Battery Charger |
| LTM-820 | 功能描述:LED 安裝硬件 LED Mount Self Ret 3 or 5mm Black RoHS:否 制造商:Bivar 產品:LED Mounting Clips LED 大小:5 mm 材料:Nylon 顏色:Black 主體長度:4.4 mm 面板厚度尺寸: 封裝:Bulk |
| LTM8328GKR04 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic |
| LTM-8328GKR-04 | 功能描述:LED 顯示器和配件 Green RoHS:否 制造商:Avago Technologies 顯示器類型:7 Segment 數位數量:2 字符大小:7.8 mm x 14.22 mm 照明顏色:Red 波長:628 nm 共用管腳:Common Anode 工作電壓:2.05 V 工作電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 35 C 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。