- 您現在的位置：買賣IC網 > PDF目錄358053 > LTL1RMTBKBINP (LITE-ON ELECTRONICS INC) T-1 SINGLE COLOR LED, BLUE, 2.95 mm PDF資料下載
參數資料
| 型號： | LTL1RMTBKBINP |
| 廠商： | LITE-ON ELECTRONICS INC |
| 元件分類： | LED |
| 英文描述： | T-1 SINGLE COLOR LED, BLUE, 2.95 mm |
| 文件頁數： | 7/8頁 |
| 文件大?。?/td> | 178K |
| 代理商： | LTL1RMTBKBINP |
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
CAUTIONS
1.
Application limitation
The LEDs described here are intended to be used for ordinary electronic equipment (such as office equipment,
communication equipment and household application.) Consult Liteon’s sales in advance for information on
application in which exceptional quality and reliability are required, particularly when the failure or malfunction
of the LEDs may directly jeopardize life or health (such as airplanes, automobiles, traffic control equipment, life
support system and safety devices).
2. Storage
After being shipped from Liteon the LEDs should be kept at 30°C or less and 70%RH or less.
The LEDs should be used within 3 months. They can be stored for a year in a sealed container with a nitrogen
atmosphere and moisture absorbent material. Please avoid rapid transitions in ambient temperature in high
humidity environments where condensation may occur.
3. Cleaning
Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED.
4. Forming & Mounting
When forming a lead, the leads should be bent at a point at least 3mm from the base of epoxy bulb. Do not use
the base of the leadframe as a fulcrum during forming. Lead forming must be done before soldering at normal
temperature. When mounted through hole type LED lamp, avoid the occurrence of residual mechanical stress
due to clinching as figure shown here.
5. Soldering
When soldering, leave a minimum of 2mm clearance from the resin to the soldering point.
Dipping the resin into the solder must be avoided.
Do not apply any stress to the lead frame during soldering while the LED is at high temperature.
Recommended soldering condition
Soldering iron
Wave soldering
Temperature
Soldering time
300°C Max.
3 sec. Max.
(one time only)
Pre-heat
Pre-heat time
Solder wave
Soldering time
100°C Max.
60 sec. Max.
260°C Max.
10 sec. Max.
6. Drive Method
LED is a current operated device, and therefore, requires some kind of current limiting incorporated into the
drive circuit. This current limiting typically takes the form of a current limiter resistor placed in series with
the LED. Consider worst case voltage variations that could occur across the current limiting resistor.
The forward current should not be allowed to change by more than 40% of its desired value.
Circuit model A
Circuit model B
LED
LED
(A) Recommended circuit.
(B) The difference of brightness between LEDs could be found due to the Vf-If characteristics of LED
Part No. : LTL1RMTBK
Page : 7 of 8
BNS-OD-C131/A4
相關PDF資料 |
PDF描述 |
|---|---|
| LTL2R3KRKBINQ | T-1 3/4 SINGLE COLOR LED, SUPER RED, 5 mm |
| LTL2U7SEKSBINW | T-1 3/4 SINGLE COLOR LED, RED, 5 mm |
| LTL2U7SYKSBINS | T-1 3/4 SINGLE COLOR LED, AMBER, 5 mm |
| LTL4HMUSJSBINLM | SINGLE COLOR LED, AMBER, 3.9 mm |
| LTL77HTBKBINL1 | T-1 SINGLE COLOR LED, BLUE, 3 mm |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTL1RMTGK | 功能描述:標準LED-通孔 Green Clear 525nm RoHS:否 制造商:Vishay Semiconductors 照明顏色:Red 光強度:0.7 mcd 波長/色溫:615 nm 顯示角:45 deg 透鏡顏色/類型:Clear, Non-Diffused 正向電流:70 mA 正向電壓:1.83 V to 3.03 V LED 大小:2 mm 系列: 封裝:Tube |
| LTL1RMTGK6 | 功能描述:標準LED-通孔 Thru-Hole Lamp 3mm Grn 525nm Clr RoHS:否 制造商:Vishay Semiconductors 照明顏色:Red 光強度:0.7 mcd 波長/色溫:615 nm 顯示角:45 deg 透鏡顏色/類型:Clear, Non-Diffused 正向電流:70 mA 正向電壓:1.83 V to 3.03 V LED 大小:2 mm 系列: 封裝:Tube |
| LTL1RMVSKNT | 制造商:Lite-On Semiconductor Corporation 功能描述:LAMP,THRU-HOLE, 3MM, INGAN, RED, 525NM, CLR - Bulk 制造商:Lite-On Semiconductor Corporation 功能描述:LAMP 3MM INGAN RED 525NM CLR |
| LTL2 | 制造商:Linrose Electronics 功能描述: |
| LTL-200uH | 制造商:P&S 功能描述:inductor |
發布緊急采購，3分鐘左右您將得到回復。