- 您現在的位置：買賣IC網 > PDF目錄5858 > LTC6416CDDB#TRMPBF (Linear Technology)IC ADC BUFFER 16BIT DIFF 10-DFN PDF資料下載
參數資料
| 型號： | LTC6416CDDB#TRMPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 3/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC BUFFER 16BIT DIFF 10-DFN |
| 標準包裝： | 500 |
| 放大器類型： | 緩沖器 |
| 電路數： | 1 |
| 輸出類型： | 差分 |
| 轉換速率： | 3400 V/µs |
| -3db帶寬： | 2GHz |
| 電流 - 輸入偏壓： | 5µA |
| 電壓 - 輸入偏移： | 500µV |
| 電流 - 電源： | 42mA |
| 電流 - 輸出 / 通道： | 20mA |
| 電壓 - 電源，單路/雙路(±)： | 2.7 V ~ 3.9 V，±1.35 V ~ 1.95 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-WFDFN 裸露焊盤 |
| 供應商設備封裝： | 10-DFN-EP（3x2） |
| 包裝： | 帶卷 (TR) |
LTC6416
11
6416f
PIN FUNCTIONS
VCM(Pin1):Thispinsetstheoutputcommonmodevoltage
seen at OUT+ and OUT– by driving IN+ and IN– through an
internal buffer with a high output resistance of 6k. The VCM
pin has a Thevenin equivalent resistance of approximately
3.8k and can be overdriven by an external voltage. If no
voltage is applied to VCM, it will oat to a default voltage
of approximately 1.25V on a 3.3V supply or 1.36V on
a 3.6V supply. The VCM pin should be bypassed with a
high-quality ceramic bypass capacitor of at least 0.1μF.
CLHI (Pin 2): High Side Clamp Voltage. The voltage applied
to the CLHI pin denes the upper voltage limit of the OUT+
and OUT– pins. This voltage should be set at least 300mV
above the upper voltage range of the driven ADC. On a 3.3V
supply, the CLHI pin will oat to a 2.23V default voltage.
On a 3.6V supply, the CLHI pin will oat to a 2.45V default
voltage. CLHI has a Thevenin equivalent of approximately
4.1kΩ and can be overdriven by an external voltage. The
CLHI pin should be bypassed with a high-quality ceramic
bypass capacitor of at least 0.1μF.
IN+,IN– (Pins 3, 4):
Non-inverting and inverting input pins
of the buffer, respectively. These pins are high impedance,
approximately 6kΩ. If AC-coupled, these pins will self bias
to the voltage present at the VCM pin.
CLLO (Pin 5): Low Side Clamp Voltage. The voltage ap-
plied to the CLLO pin denes the lower voltage limit of
the OUT+ and OUT– pins. This voltage should be set at
least 300mV below the lower voltage range of the driven
ADC. On a 3.3V supply, the CLLO pin will oat to a 0.25V
default voltage. On a 3.6V supply, the CLLO pin will oat to
a 0.265V default voltage. CLLO has a Thevenin equivalent
resistance of approximately 2.3k and can be overdriven by
an external voltage. The CLLO pin should be bypassed with
a high quality ceramic bypass capacitor of at least 0.1μF.
GND (Pins 6, 9, 11): Negative power supply, normally
tied to ground. Both pins and the exposed paddle must
be tied to the same voltage. GND may be tied to a voltage
other than ground as long as the voltage between V+ and
GND is 2.7V to 4V. If the GND pins are not tied to ground,
bypass them with 680pF and 0.1μF capacitors as close to
the package as possible.
OUT–, OUT+ (Pins 7, 8):
Outputs. The LTC6416 outputs
are low impedance. Each output has an output impedance
of approximately 9Ω at DC.
V+ (Pin 10):
Positive Power Supply. Typically 3.3V to 3.6V.
Split supplies are possible as long as the voltage between
V+ and GND is 2.7V to 4V. Bypass capacitors of 680pF
and 0.1μF as close to the part as possible should be used
between the supplies.
Exposed Pad (Pin 11): Ground. The exposed pad must
be soldered to the printed circuit board ground plane for
good heat transfer. If GND is a voltage other than ground,
the Exposed Pad must be connected to a plane with the
same potential as the GND pins – Not to the system
ground plane.
DC TEST CIRCUIT SCHEMATIC
8
1
2
3
4
5
6
9
11
7
CLOAD
V+
10
OUT
–
6416 DC
OUT+
OUT
–
OUT+
RLOAD
VCM
IN+
CLHI
CLLO
IN–
LTC6416
VINDIFF = IN
+ – IN–
IN+ + IN–
2
VINCM =
VOUTDIFF = OUT
+ – OUT–
OUT+ + OUT–
2
VOUTCM =
相關PDF資料 |
PDF描述 |
|---|---|
| 76383-302 | CONN HEADER 4PS .100 DL R/A GOLD |
| LTC6416CDDB#TRPBF | IC ADC BUFFER 16BIT DIFF 10-DFN |
| 77317-103-08LF | BERGSTIK |
| LTC2052IS#TRPBF | IC OP-AMP ZERO-DRIFT QUAD 14SOIC |
| TLW-131-06-G-D | CONN HEADER .100" 62POS DL GOLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC6416CDDB-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:2 GHz Low Noise Differential 16-Bit ADC Buffer |
| LTC6416IDDB#PBF | 制造商:Linear Technology 功能描述:Differiential Amplifier IC 制造商:Linear Technology 功能描述:IC, DIFFERENTIAL AMP, 2GHZ 3.4V/NS DFN10; No. of Amplifiers:1; Input Offset Voltage:5mV; Bandwidth:2GHz; Amplifier Case Style:DFN; No. of Pins:10; Supply Voltage Range:2.7V to 3.9V; Slew Rate:3.4V/ns; Supply Current:42mA ;RoHS Compliant: Yes |
| LTC6416IDDB#TRMPBF | 功能描述:IC DIFF 16BIT BUFFER 10-DFN RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:45nA 電壓 - 輸入偏移:2000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:40mA 電壓 - 電源，單路/雙路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) 其它名稱:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
| LTC6416IDDB#TRPBF | 功能描述:IC DIFF 16BIT BUFFER 10-DFN RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:3.5 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:30pA 電壓 - 輸入偏移:2000µV 電流 - 電源:200µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 |
| LTC6416IDDB-TRMPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:2 GHz Low Noise Differential 16-Bit ADC Buffer |
發布緊急采購，3分鐘左右您將得到回復。