- 您現在的位置：買賣IC網 > Datasheet目錄42 > LTC4300-1IMS8#TRPBF (Linear Technology)IC HOTSWAP 2WIRE BUS BUFFR 8MSOP Datasheet資料下載
參數資料
| 型號： | LTC4300-1IMS8#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 8/18頁 |
| 文件大?。?/td> | 735K |
| 描述： | IC HOTSWAP 2WIRE BUS BUFFR 8MSOP |
| 標準包裝： | 2,500 |
| 類型： | 熱交換開關 |
| 應用： | 通用型緩沖器/總線擴展器 |
| 內部開關： | 是 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-MSOP |
| 包裝： | 帶卷 (TR) |
TC4300-1/LTC4300-2
8
430012fb
For more information www.linear.com/LTC4300-1
operaTion
Start-Up
When the LTC4300 first receives power on its V
CC
pin,
either during power-up or during hot swapping, it starts
in an undervoltage lockout (UVLO) state, ignoring any
activity on the SDA and SCL pins until V
CC
rises above
2.5V. For the LTC4300-2, the part also waits for V
CC2
to
rise above 2V. This ensures that the part does not try to
function until it has enough voltage to do so.
During this time, the 1V precharge circuitry is also ac-
tive and forces 1V through 100k nominal resistors to the
SDA and SCL pins. Because the I/O card is being plugged
into a live backplane, the voltage on the backplane SDA
and SCL busses may be anywhere between 0V and V
CC
.
Precharging the SCL and SDA pins to 1V minimizes the
worst-case voltage differential these pins will see at the
moment of connection, therefore minimizing the amount
of disturbance caused by the I/O card.
Once the LTC4300 comes out of UVLO, it assumes that
SDAIN and SCLIN have been hot swapped into a live sys-
tem and that SDAOUT and SCLOUT are being powered up
at the same time as itself. Therefore, it looks for either a
STOP bit or bus idle condition on the backplane side to
indicate the completion of a data transaction. When either
one occurs, the part also verifies that both the SDAOUT
and SCLOUT voltages are high. When all of these condi
-
tions are met, the input-to-output connection circuitry is
activated, joining the SDA and SCL busses on the I/O card
with those on the backplane.
Connection Circuitry
Once the connection circuitry is activated, the functionality
of the SDAIN and SDAOUT pins is identical. A LOW forced
on either pin at any time results in both pin voltages being
LOW. SDAIN and SDAOUT enter a logic HIGH state only
when all devices on both SDAIN and SDAOUT force a HIGH.
The same is true for SCLIN and SCLOUT. This important
feature ensures that clock stretching, clock arbitration
and the acknowledge protocol always work, regardless
of how the devices in the system are tied to the LTC4300.
Another key feature of the connection circuitry is that it
provides bidirectional buffering, keeping the backplane
and card capacitances isolated. Because of this isolation,
the waveforms on the backplane busses look slightly
different than the corresponding card bus waveforms, as
described here.
Input to Output Offset Voltage
When a logic LOW voltage, V
LOW1
, is driven on any of
the LTC4300s data or clock pins, the LTC4300 regulates
the voltage on the other side of the chip (call it V
LOW2
)
to a slightly higher voltage, as directed by the following
equation:
V
LOW2
= V
LOW1
+ 50mV + (V
CC
/R) " 100
where R is the bus pull-up resistance in ohms. For
example, if a device is forcing SDAOUT to 10mV and if
V
CC
= 3.3V and the pull-up resistor R on SDAIN is 10k,
then the voltage on SDAIN = 10mV + 50mV + (3.3/10000)
" 100 = 93mV. See the Typical Performance Characteristics
section for curves showing the offset voltage as a function
of V
CC
and R.
Propagation Delays
During a rising edge, the rise time on each side is deter-
mined by the combined pull-up current of the LTC4300
boost current and the bus resistor and the equivalent
capacitance on the line. If the pull-up currents are the
same, a difference in rise time occurs which is directly
proportional to the difference in capacitance between the
two sides. This effect is displayed in Figure 1 for V
CC
=
3.3V and a 10k pull-up resistor on each side (50pF on
one side and 150pF on the other). Since the output side
has less capacitance than the input, it rises faster and the
effective t
PLH
is negative.
There is a finite propagation delay, t
PHL
, through the con-
nection circuitry for falling waveforms. Figure 2 shows
the falling edge waveforms for the same V
CC
, pull-up
resistors and equivalent capacitance conditions as used
in Figure 1. An external NMOS device pulls down the
voltage on the side with 150pF capacitance; the LTC4300
pulls down the voltage on the opposite side, with a delay
of 55ns. This delay is always positive and is a function of
supply voltage, temperature and the pull-up resistors and
equivalent bus capacitances on both sides of the bus. The
Typical Performance Characteristics section shows t
PHL
as a function of temperature and voltage for 10k pull-up
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4300A-2IMS8#TRPBF | IC BUFFER BUS 2WR HOTSWAP 8-MSOP |
| LTC4301IDD | IC BUFFER BUS HOTSWAP 2WR 8DFN |
| LTC4301LIDD#TRPBF | IC BUFFER BUS HOTSWAP 2WR 8DFN |
| LTC4302IMS-1#TRPBF | IC BUFFER 2-WIRE BUS 10-MSOP |
| LTC4303CDD#TRPBF | IC BUS BUFFER I2C 8-DFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4300-2CMS8 | 功能描述:IC HOT SWAP 2WIRE BUS BUFR MSOP8 RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LTC4300-2CMS8#PBF | 功能描述:IC HOTSWAP 2WIRE BUS BUFFR 8MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LTC4300-2CMS8#TR | 功能描述:IC BUFFER BUS HOTSWAP 2WR 8MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LTC4300-2CMS8#TRPBF | 功能描述:IC HOTSWAP 2WIRE BUS BUFFR 8MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LTC4300-2IMS8 | 功能描述:IC BUFFER BUS HOTSWAP 2WR 8MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。