參數資料
型號： LTC4300-1IMS8#TRPBF
廠商： Linear Technology
文件頁數： 11/18頁
文件大小： 735K
描述： IC HOTSWAP 2WIRE BUS BUFFR 8MSOP
標準包裝： 2,500
類型： 熱交換開關
應用： 通用型緩沖器/總線擴展器
內部開關： 是
電源電壓： 2.7 V ~ 5.5 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 8-TSSOP，8-MSOP（0.118"，3.00mm 寬）
供應商設備封裝： 8-MSOP
包裝： 帶卷 (TR)
LTC4300-1/LTC4300-2
11
430012fb
For more information www.linear.com/LTC4300-1
associated with hot swapping have settled. Owing to
their small capacitance, the SDAIN and SCLIN pins cause
minimal disturbance on the backplane busses when they
make contact with the connector.
Figure 6 shows the LTC4300-2 in a CompactPCI con-
figuration. The LTC4300-2 receives its V
CC
 voltage from
one of the long early power pins. Because this power
is not switched, add a 5?to 10?resistor between the
V
CC
 pins of the connector and the LTC4300-2, as shown
in the figure. In addition, make sure that the V
CC
 bypass-
ing on the backplane is large compared to the 0.01礔
bypass capacitor on the card. Establishing early power
V
CC
 ensures that the 1V precharge voltage is present at
the SDAIN and SCLIN pins before they make contact.
Connect V
CC2
 to the output of one of the CompactPCI
power supply Hot Swap circuits. V
CC2
 is monitored by
a filtered UVLO circuit. With the V
CC2
 voltage powering
up after all other pins have established connection, the
UVLO circuit ensures that the backplane and card data
and clock busses are not connected until the transients
associated with hot swapping have settled.
Figure 7 shows the LTC4300-1 in a PCI application, where
all of the pins have the same length. In this case, connect
an RC series circuit on the I/O card between V
CC
 and
ENABLE. An RC product of 10ms provides a filter to prevent
the LTC4300-1 from becoming activated until the transients
associated with hot swapping have settled.
Figure 8 shows the LTC4300-2 in an application where the
user has a custom connector with pins of three different
lengths available. Making V
CC2
 the shortest pin ensures
that all other pins are firmly connected before V
CC2
 
receives any voltage. A filtered UVLO circuit on V
CC2
 
ensures that the V
CC2
 pin is firmly connected before the
LTC4300-2 connects the backplane to the card.
Repeater/Bus Extender Application
Users who wish to connect two 2-wire systems separated
by a distance can do so by connecting two LTC4300-1s
back-to-back, as shown in Figure 9. The I
2
C specification
allows for 400pF maximum bus capacitance, severely
limiting the length of the bus. The SMBus specification
places no restriction on bus capacitance, but the limited
impedances of devices connected to the bus require sys-
tems to remain small if rise and fall time specifications
are to be met. The strong pull-up and pull-down imped-
ances of the LTC4300-1 are capable of meeting rise and
fall time specifications for one nanofarad of capacitance,
thus allowing much more interconnect distance. In this
situation, the differential ground voltage between the two
systems may limit the allowed distance, because a valid
logic LOW voltage with respect to the ground at one end
of the system may violate the allowed V
OL
 specification
with respect to the ground at the other end. In addition,
the connection circuitry offset voltages of the back-to-
back LTC4300-1s add together, directly contributing to
the same problem.
Systems with Disparate Supply Voltages (LTC4300-1)
In large 2-wire systems, the V
CC
 voltages seen by devices
at various points in the system can differ by a few hun-
dred millivolts or more. This situation is well modelled by
a series resistor in the V
CC
 line, as shown in Figure 10.
For proper operation of the LTC4300-1, make sure that
V
CC(BUS)
 e V
CC(LTC4300)
  0.5V.
5V to 3.3V Level Translator and Power Supply
Redundancy (LTC4300-2)
Systems requiring different supply voltages for the back-
plane side and the card side can use the LTC4300-2, as
shown in Figure 11. The pull-up resistors on the card side
connect from SDAOUT to SCLOUT to V
CC2
, and those on
the backplane side connect from SDAIN and SCLIN to V
CC
.
The LTC4300-2 functions for voltages ranging from 2.7V
to 5.5V on both V
CC
 and V
CC2
. There is no constraint on
the voltage magnitudes of V
CC
 and V
CC2
 with respect to
each other.
This application also provides power supply redundancy.
If either the V
CC
 or V
CC2
 voltage falls below its UVLO
threshold, the LTC4300-2 disconnects the backplane
from the card, so that the side that is still powered can
continue to function.
applicaTions inFormaTion
相關PDF資料
PDF描述
LTC4300A-2IMS8#TRPBF IC BUFFER BUS 2WR HOTSWAP 8-MSOP
LTC4301IDD IC BUFFER BUS HOTSWAP 2WR 8DFN
LTC4301LIDD#TRPBF IC BUFFER BUS HOTSWAP 2WR 8DFN
LTC4302IMS-1#TRPBF IC BUFFER 2-WIRE BUS 10-MSOP
LTC4303CDD#TRPBF IC BUS BUFFER I2C 8-DFN
相關代理商/技術參數
參數描述
LTC4300-2CMS8 功能描述:IC HOT SWAP 2WIRE BUS BUFR MSOP8 RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件
LTC4300-2CMS8#PBF 功能描述:IC HOTSWAP 2WIRE BUS BUFFR 8MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件
LTC4300-2CMS8#TR 功能描述:IC BUFFER BUS HOTSWAP 2WR 8MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件
LTC4300-2CMS8#TRPBF 功能描述:IC HOTSWAP 2WIRE BUS BUFFR 8MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件
LTC4300-2IMS8 功能描述:IC BUFFER BUS HOTSWAP 2WR 8MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*