參數資料
型號： LTC4280CUFD#PBF
廠商： Linear Technology
文件頁數： 8/28頁
文件大小： 291K
描述： IC CONTROLLER HOT SWAP QFN-24
標準包裝： 73
類型： 熱交換控制器
應用： 通用
內部開關： 無
電源電壓： 2.9 V ~ 15 V
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 24-WFQFN 裸露焊盤
供應商設備封裝： 24-QFN（5x4）
包裝： 管件
LTC4280
8
4280f
 PIN FUNCTIONS
ADIN:  ADC  Input.  A  voltage  between  0V  and  1.235V 
applied to this pin is measured by the onboard ADC. Tie
to ground if unused.
ADR0, ADR1, ADR2: Serial Bus Address Inputs. Tying 
these pins to ground, to the INTV
CC
 pin or open con gures
one of 27 possible addresses. See Table 1 in Applications
Information.
ALERT: Fault Alert Output. Open-drain logic output that 
is pulled to ground when a fault occurs to alert the host
controller. A fault alert is enabled by the ALERT register.
See Applications Information. Tie to ground if unused.
EN: Enable Input. Ground this pin to indicate a board is 
present and enable the N-channel MOSFET to turn on. When
this pin is high, the MOSFET is not allowed to turn on. An
internal 10糀 current source pulls up this pin. Transitions
on this pin are recorded in the Fault register. A high-to-low
transition activates the logic to read the state of the ON pin
and clear Faults. See Applications Information.
EXPOSED PAD (Pin 25): Exposed pad may be left open 
or connected to device ground.
FB:  Foldback  Current  Limit  and  Power  Good  Input.  A 
resistive divider from the output is tied to this pin. When
the voltage at this pin drops below 1.235V, power is not
considered good. The power bad condition may result in the
GPIO pin pulling low or going high impedance depending
on the con guration of control register bits A6 and A7.
Also a power bad fault is logged in this condition if the
LTC4280 has  nished the start-up cycle and the GATE pin
is high. See Applications Information. The current limit
folds back from a 26mV sense voltage to 10mV as the
FB pin voltage falls from 0.6V to 0V.
FILTER: Fault Filter Input. Connect a capacitor between this 
pin and ground to set a 123ms/糉 delay for overcurrent
fault  ltering after startup.
GATE: Gate Drive for External N-Channel MOSFET. An 
internal 20糀 current source charges the gate of the
MOSFET. Often no compensation capacitor is required
on the GATE pin, but a resistor and capacitor network
from this pin to ground may be used to set the turn-on
output voltage slew rate. See Applications Information.
During turn-off there is a 1mA pulldown current. During
a short-circuit or undervoltage lockout (V
DD
 or INTV
CC
),
a 450mA pulldown current source between GATE and
SOURCE is activated.
GND: Device Ground.
GPIO: General Purpose Input/Output. Open-drain logic 
output or logic input. Defaults to an output set to pull
low to indicate power is not good. Con gure according
to Table 2 and 3.
INTV
CC
: Low Voltage Supply Decoupling Output. Connect 
a 0.1糉 capacitor from this pin to ground.
ON: On Control Input. A rising edge turns on the external 
N-channel MOSFET and a falling edge turns it off. This pin
also con gures the state of the FET On bit in the control
register (and hence the external MOSFET) at power up.
For example, if the ON pin is tied high, then the FET On bit
(A3 in Table 2) goes high 100ms after power-up. Likewise
if the ON pin is tied low then the part remains off after
power-up until the FET On bit is set high using the I
2
C
bus. A high-to-low transition on this pin clears the fault
register.
OV: Overvoltage Comparator Input. Connect this pin to an 
external resistive divider from V
DD
. If the voltage at this
pin rises above 1.235V, an overvoltage fault is detected
and the GATE turns off. Tie to GND if unused.
相關PDF資料
PDF描述
LTC4300-1IMS8#TRPBF IC HOTSWAP 2WIRE BUS BUFFR 8MSOP
LTC4300A-2IMS8#TRPBF IC BUFFER BUS 2WR HOTSWAP 8-MSOP
LTC4301IDD IC BUFFER BUS HOTSWAP 2WR 8DFN
LTC4301LIDD#TRPBF IC BUFFER BUS HOTSWAP 2WR 8DFN
LTC4302IMS-1#TRPBF IC BUFFER 2-WIRE BUS 10-MSOP
相關代理商/技術參數
參數描述
LTC4280CUFD-TR 制造商:LINER 制造商全稱:Linear Technology 功能描述:Hot Swap Controller with I2C Compatible Monitoring
LTC4280CUFD-TRPBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:Hot Swap Controller with I2C Compatible Monitoring
LTC4280IUFD 制造商:LINER 制造商全稱:Linear Technology 功能描述:Hot Swap Controller with I2C Compatible Monitoring
LTC4280IUFD#PBF 功能描述:IC HOT SWAP CONTROLLER 24-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF)
LTC4280IUFD#TRPBF 功能描述:IC CTLR HOT SWAP I2C MON 24QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*