- 您現在的位置：買賣IC網 > Datasheet目錄42 > LTC4280CUFD#PBF (Linear Technology)IC CONTROLLER HOT SWAP QFN-24 Datasheet資料下載
參數資料
| 型號： | LTC4280CUFD#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 14/28頁 |
| 文件大?。?/td> | 291K |
| 描述： | IC CONTROLLER HOT SWAP QFN-24 |
| 標準包裝： | 73 |
| 類型： | 熱交換控制器 |
| 應用： | 通用 |
| 內部開關： | 無 |
| 電源電壓： | 2.9 V ~ 15 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 24-QFN（5x4） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LTC4280
14
4280f
APPLICATIONS INFORMATION
When the MOSFET is turning on, the inrush current follows
the foldback pro le as shown in Figure 2. Meanwhile the
FILTER pin is held low with 0.6mA to prevent the FILTER
pin from generating an overcurrent fault during start-up.
The TIMER pin integrates at 100糀 during start-up and
once it reaches its threshold of 1.235V, the part checks
to see if it is in current limit, which indicates that it has
started up into a short-circuit condition. If this is the case,
the overcurrent fault bit, D2 in Table 5, is set and the part
turns off. If the part is not in current limit, the FILTER pin
is released to enable circuit breaker and current limit based
overcurrent faults. Alternately an internal 100ms start-up
timer may be selected by tying the TIMER pin to INTV
CC
.
a 20糀 pull-up current from the gate pin slews the gate
upwards and the part is not in current limit. The start-up
TIMER may expire in this condition and an OC fault is not
generated even though start-up has not completed. Either
the sense voltage increases to the 25mV CB threshold or
the current limit as set by the FB pin which generates an
OC fault when the FILTER pin reaches its 1.235V threshold,
or the FB pin voltage crosses its 1.235V power good
threshold and the GPIO pin signals power good.
GATE Pin Voltage
A curve of gate-to-source drive vs V
DD
is shown in the
Typical Performance Characteristics. At minimum input
supply voltage of 2.9V, the minimum gate-to-source drive
voltage is 4.7V. The gate-to-source voltage is clamped
below 6.5V to protect the gates of logic level N-channel
MOSFETs.
Turn-Off Sequence
The GATE is turned off by a variety of conditions. A normal
turn-off is initiated by the ON pin going low or a serial bus
turn-off command. Additionally, several fault conditions
turn off the GATE. These include an input overvoltage
(OV pin), input undervoltage (UV pin), overcurrent circuit
breaker (SENSE
pin), or EN transitioning high. Writing
a logic one into the UV, OV or OC fault bits (D0-D2 in
Table 5) also latches off the GATE if their auto-retry bits
are set to false.
Normally the MOSFET is turned off with a 1mA current
pulling down the GATE pin to ground. With the MOSFET
turned off, the SOURCE and FB voltages drop as C
L
discharges. When the FB voltage crosses below its
threshold, GPIO pulls low to indicate that the output power
is no longer good.
If the V
DD
pin falls below 2.74V for greater than 2約 or
INTV
CC
drops below 2.60V for greater than 1約, a fast shut
down of the MOSFET is initiated. The GATE pin is pulled
down with a 450mA current to the SOURCE pin.
V
DD
+ 6V
V
GATE
V
OUT
GPIO1
(POWER GOOD)
I
LOAD
" R
SENSE
V
DD
V
SENSE
25mV
10mV
FB
LIMITED
4280 F02
TIMER
EXPIRES
t
STARTUP
Figure 2. Power-Up Waveforms
As the SOURCE voltage rises, the FB pin follows as set
by R7 and R8. Once FB crosses its 1.235V threshold, and
the start-up timer has expired, the GPIO pin, in its default
con guration, ceases to pull low and indicates that power
is now good.
If R6 and C1 are employed for a constant current during
start-up, which produces a constant dV/dt at the output,
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4300-1IMS8#TRPBF | IC HOTSWAP 2WIRE BUS BUFFR 8MSOP |
| LTC4300A-2IMS8#TRPBF | IC BUFFER BUS 2WR HOTSWAP 8-MSOP |
| LTC4301IDD | IC BUFFER BUS HOTSWAP 2WR 8DFN |
| LTC4301LIDD#TRPBF | IC BUFFER BUS HOTSWAP 2WR 8DFN |
| LTC4302IMS-1#TRPBF | IC BUFFER 2-WIRE BUS 10-MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4280CUFD-TR | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Hot Swap Controller with I2C Compatible Monitoring |
| LTC4280CUFD-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Hot Swap Controller with I2C Compatible Monitoring |
| LTC4280IUFD | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Hot Swap Controller with I2C Compatible Monitoring |
| LTC4280IUFD#PBF | 功能描述:IC HOT SWAP CONTROLLER 24-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4280IUFD#TRPBF | 功能描述:IC CTLR HOT SWAP I2C MON 24QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。