參數資料
型號: LTC4278CDKD#PBF
廠商: Linear Technology
文件頁數: 3/42頁
文件大?。?/td> 0K
描述: IC PD IEEE 802.3AT 25.5W 32-DFN
產品培訓模塊: Power over Ethernet
標準包裝: 52
控制器類型: 供電設備接口控制器(PD)
接口: IEEE 802.3af
電源電壓: 4.5 V ~ 20 V
電流 - 電源: 6.4mA
工作溫度: 0°C ~ 70°C
安裝類型: 表面貼裝
封裝/外殼: 32-WFDFN 裸露焊盤
供應商設備封裝: 32-DFN(7x4)裸露焊盤
包裝: 管件
產品目錄頁面: 1338 (CN2011-ZH PDF)
LTC4278
11
4278fc
Information section for details. This pin is used for the
UVLO function of the switching regulator. The PD interface
section has an internal UVLO.
SENSE, SENSE+ (Pins 19, 20): Current Sense Inputs.
These pins are used to measure primary-side switch cur-
rent through an external sense resistor. Peak primary-side
current is used in the converter control loop. Make Kelvin
connections to the sense resistor RSENSE to reduce noise
problems.SENSEconnectstotheGNDside.Atmaximum
current (VCMP at its maximum voltage) SENSE pins have
100mV threshold. The signal is blanked (ignored) during
the minimum turn-on time.
CCMP (Pin 21): Load Compensation Capacitive Control.
Connect a capacitor from CCMP to GND in order to reduce
the effects of parasitic resistances in the feedback sensing
path. A 0.1F ceramic capacitor suffices for most applica-
tions. Short this pin to GND when load compensation is
not needed.
RCMP (Pin 22): Load Compensation Resistive Control.
Connect a resistor from RCMP to GND in order to com-
pensate for parasitic resistances in the feedback sensing
path. In less demanding applications, this resistor is not
needed and this pin can be left open. See the Applications
Information section for details.
PIN FUNCTIONS
PGDLY (Pin 23): Primary Gate Delay Control. Connect an
external programming resistor (RPGDLY) to set delay from
synchronous gate turn-off to primary gate turn-on. See
the Applications Information section for details.
PG (Pin 24): Primary Gate Drive. PG is the gate drive pin
for the primary-side MOSFET switch. Large dynamic cur-
rents flow during voltage transitions. See the Applications
Information section for details.
VNEG (Pins 26, 27): System Negative Rail. Connects VNEG
to VPORTN through an internal power MOSFET. Pin 26 and
Pin 27 must be electrically tied together at the package.
PWRGD (Pin 29): Power Good Output, Open-Collector.
High impedance signals power-up completion. PWRGD
is referenced to VNEG and features a 14V clamp.
PWRGD (Pin 30): Complementary Power Good Output,
Open-Drain.Lowimpedancesignalspower-upcompletion.
PWRGD is referenced to VPORTN.
VPORTP (Pin 32): Positive Power Input. Tie to the input
port power through the input diode bridge.
Exposed Pad (Pin 33): Ground. This is the negative rail
connection for both signal ground and gate driver grounds
of the flyback controller. This pin should be connected to
VNEG.
相關PDF資料
PDF描述
KSZ8873MLL IC ETHERNET SWITCH 3PORT 64-LQFP
KSZ8863RLL IC ETHERNET SW 3PORT 48-LQFP
KSZ8863MLL IC ETHERNET SW 3PORT 48-LQFP
KSZ8863FLL IC ETHERNET SW 3PORT 48-LQFP
LTC4267IDHC#PBF IC POE 802.3AF INTERFACE 16-DFN
相關代理商/技術參數
參數描述
LTC4278CDKDTRPBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:IEEE 802.3at PD with Synchronous No-Opto Flyback Controller and 12V Aux Support
LTC4278IDKD 制造商:LINER 制造商全稱:Linear Technology 功能描述:IEEE 802.3at PD with Synchronous No-Opto Flyback Controller and 12V Aux Support
LTC4278IDKD#PBF 功能描述:IC PD IEEE 802.3AT 25.5W 32-DFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C,串行,SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN(4x4) 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND
LTC4278IDKD#TRPBF 功能描述:IC PD IEEE 802.3AT 25.5W 32-DFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C,串行,SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN(4x4) 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND
LTC4278IDKDPBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:IEEE 802.3at PD with Synchronous No-Opto Flyback Controller and 12V Aux Support