參數資料
型號: LTC4267CDHC
廠商: LINEAR TECHNOLOGY CORP
元件分類: 穩壓器
英文描述: RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
中文描述: 1 A SWITCHING CONTROLLER, 240 kHz SWITCHING FREQ-MAX, PDSO16
封裝: 5 X 3 MM, PLASTIC, MO-229-WJED-1, DFN-16
文件頁數: 8/32頁
文件大?。?/td> 1975K
代理商: LTC4267CDHC
LTC4267
8
4267f
I
TH
/RUN (Pin 2/Pin 1):
Current Threshold/Run Input. This
pin performs two functions. It serves as the switching
regulator error amplifier compensation point as well as
the run/shutdown control input. Nominal voltage range is
0.7V to 1.9V. Forcing the pin below 0.28V with respect to
PGND causes the controller to shut down.
PGND (Pin 1, 8, 9, 16/Pin 2, 15):
Switching Regulator
Negative Supply. This pin is the negative supply rail for the
switching regulator controller and must be tied to P
OUT
.
NGATE (Pin 3/Pin 3):
Gate Driver Output. This pin drives
the regulator’s external N-Channel MOSFET and swings
from PGND to P
VCC
.
P
VCC
(Pin 4/Pin 4):
Switching Regulator Positive Supply.
This pin is the positive supply rail for the switching regula-
tor and must be closely decoupled to PGND.
R
CLASS
(Pin 5/Pin 5):
Class Select Input. Used to set the cur-
rent value the PD maintains during classification. Connect
a resistor between R
CLASS
and V
PORTN
(see Table 2).
V
PORTN
(Pin 7/Pin 7):
Negative Power Input. Tie to the
–48V input port through the input diodes.
P
OUT
(Pin 10/Pin 10):
Power Output. Supplies –48V to
the switching regulator PGND pin and any additional PD
loads through an internal power MOSFET that limits input
current. P
OUT
is high impedance until the voltage reaches
the turn-on UVLO threshold. The output is then current
limited. See the Application Information section.
P
W
R
G
D (Pin 11/Pin 11):
Power Good Output, Open-Drain.
Indicates that the PD MOSFET is on and the switching
regulator can start operation. Low impedance indicates
power is good.
P
W
R
G
D is high impedance during detec-
tion, classification and in the event of a thermal overload.
P
W
R
G
D is referenced to V
PORTN
.
SIGDISA (Pin 12/Pin 12):
Signature Disable Input. SIGDISA
allows the PD to present an invalid signature resistance
and remain inactive. Connecting SIGDISA to V
PORTP
lowers
the signature resistance to an invalid value and disables
all functions of the LTC4267. If unused, tie SIGDISA to
V
PORTN
.
V
PORTP
(Pin 13/Pin 13):
Positive Power Input. Tie to the
input port power return through the input diodes.
SENSE (Pin 14/Pin 14):
Current Sense. This pin performs
two functions. It monitors the regulator switch current by
reading the voltage across an external sense resistor. It also
injects a current ramp that develops a slope compensation
voltage across an optional external programming resistor.
See the Applications Information section.
V
FB
(Pin 15/Pin 16):
Feedback Input. Receives the feed-
back voltage from the external resistor divider across the
output.
NC (Pin 6/Pin 6, 8, 9):
No Internal Connection.
Backside Connection (DHC Only, Pin 17):
Exposed Pad.
This exposed pad must be soldered to an electrically isolated
and thermally conductive PC board heat sink.
(GN/DHC)
PIU
相關PDF資料
PDF描述
LTC1737 RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
LTC4257-1 Power over Ethernet Interface Controller with Dual Current Limit
LTC4257CDD-1 Power over Ethernet Interface Controller with Dual Current Limit
LTC4267 RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
LTC4267IDHC RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
相關代理商/技術參數
參數描述
LTC4267CDHC#PBF 功能描述:IC POE 802.3AF INTERFACE 16-DFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C,串行,SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN(4x4) 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND
LTC4267CDHC#TRPBF 功能描述:IC POE 802.3AF INTERFACE 16-DFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C,串行,SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN(4x4) 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND
LTC4267CDHC-3 制造商:LINER 制造商全稱:Linear Technology 功能描述:Power over Ethernet IEEE 802.3af PD Interface with Integrated Switching Regulator
LTC4267CDHC-3#PBF 功能描述:IC POE 802.3AF W/REG 16-DFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C,串行,SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN(4x4) 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND
LTC4267CDHC-3#TRPBF 功能描述:IC POE 802.3AF INTERFACE 16-DFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C,串行,SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN(4x4) 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND