- 您現在的位置：買賣IC網 > PDF目錄377778 > LTC4267CDHC (LINEAR TECHNOLOGY CORP) RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS PDF資料下載
參數資料
| 型號： | LTC4267CDHC |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| 中文描述： | 1 A SWITCHING CONTROLLER, 240 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | 5 X 3 MM, PLASTIC, MO-229-WJED-1, DFN-16 |
| 文件頁數： | 19/32頁 |
| 文件大?。?/td> | 1975K |
| 代理商： | LTC4267CDHC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
LTC4267
19
4267f
APPLICATIOU
Signature Disable Interface
To disable the 25k
Ω
signature resistor, connect SIGDISA pin
to the V
PORTP
pin. Alternately, SIGDISA pin can be driven
high with respect to V
PORTN
. An example of a signature
disable interface is shown in Figure 16, option 2. Note that
the SIGDISA input resistance is relatively large and the
threshold voltage is fairly low. Because of high voltages
present on the printed circuit board, leakage currents from
the V
PORTP
pin could inadvertently pull SIGDISA high. To
ensure trouble-free operation, use high voltage layout
techniques in the vicinity of SIGDISA. If unused, connect
SIGDISA to V
PORTN
.
W
U
U
Load Capacitor
The IEEE 802.3af specification requires that the PD maintain
a minimum load capacitance of 5μF (provided by C1 in
Figure 11). It is permissible to have a much larger load
capacitor and the LTC4267 can charge very large load
capacitors before thermal issues become a problem. The
load capacitor must be large enough to provide sufficient
energy for proper operation of the switching regulator.
However, the capacitor must not be too large or the PD
design may violate IEEE 802.3af requirements.
If the load capacitor is too large, there can be a problem
with inadvertent power shutdown by the PSE. Consider
the following scenario. If the PSE is running at –57V
(maximum allowed) and the PD has detected and powered
up, the load capacitor will be charged to nearly –57V. If
for some reason the PSE voltage is suddenly reduced to
–44V (minimum allowed), the input bridge will reverse bias
and the PD power will be supplied by the load capacitor.
Depending on the size of the load capacitor and the DC load
of the PD, the PD will not draw any power for a period of
time. If this period of time exceeds the IEEE 802.3af 300ms
disconnect delay, the PSE will remove power from the PD.
For this reason, it is necessary to ensure that inadvertent
shutdown cannot occur.
Very small output capacitors (≤10μF) will charge very
quickly in current limit. The rapidly changing voltage at
the output may reduce the current limit temporarily, caus-
ing the capacitor to charge at a somewhat reduced rate.
Conversely, charging a very large capacitor may cause the
current limit to increase slightly. In either case, once the
output voltage reaches its final value, the input current
limit will be restored to its nominal value.
The load capacitor can store significant energy when fully
charged. The design of a PD must ensure that this energy
is not inadvertently dissipated in the LTC4267. The polar-
ity-protection diode(s) prevent an accidental short on the
cable from causing damage. However, if the V
PORTN
pin
is shorted to V
PORTP
inside the PD while the capacitor
is charged, current will flow through the parasitic body
diode of the internal MOSFET and may cause permanent
damage to the LTC4267.
Maintain Power Signature
In an IEEE 802.3af system, the PSE uses the maintain
power signature (MPS) to determine if a PD continues to
require power. The MPS requires the PD to periodically
draw at least 10mA and also have an AC impedance less
than 26.25k
Ω
in parallel with 0.05μF. If either the DC
current is less than 10mA or the AC impedance is above
26.25k
Ω
,
the PSE may disconnect power. The DC current
must be less than 5mA and the AC impedance must be
above 2M
Ω
to guarantee power will be removed.
Selecting Feedback Resistor Values
The regulated output voltage of the switching regulator is
determined by the resistor divider across V
OUT
(R1 and
R2 in Figure 11) and the error amplifier reference voltage
V
REF
. The ratio of R2 to R1 needed to produce the desired
voltage can be calculated as:
R2 = R1 (V
OUT
– V
REF
)/V
REF
In an isolated power supply application, V
REF
is determined
by the designer’s choice of an external error amplifier.
Commercially available error amplifiers or programmable
shunt regulators may include an internal reference of
1.25V or 2.5V. Since the LTC4267 internal reference and
error amplifier are not used in an isolated design, tie the
V
FB
pin to PGND.
In a nonisolated power supply application, the LTC4267
onboard internal reference and error amplifier can be
used. The resistor divider output can be tied directly to
the V
FB
pin. The internal reference of the LTC4267 is 0.8V
nominal.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1737 | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LTC4257-1 | Power over Ethernet Interface Controller with Dual Current Limit |
| LTC4257CDD-1 | Power over Ethernet Interface Controller with Dual Current Limit |
| LTC4267 | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LTC4267IDHC | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4267CDHC#PBF | 功能描述:IC POE 802.3AF INTERFACE 16-DFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND |
| LTC4267CDHC#TRPBF | 功能描述:IC POE 802.3AF INTERFACE 16-DFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND |
| LTC4267CDHC-3 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Power over Ethernet IEEE 802.3af PD Interface with Integrated Switching Regulator |
| LTC4267CDHC-3#PBF | 功能描述:IC POE 802.3AF W/REG 16-DFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND |
| LTC4267CDHC-3#TRPBF | 功能描述:IC POE 802.3AF INTERFACE 16-DFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND |
發布緊急采購，3分鐘左右您將得到回復。