- 您現在的位置：買賣IC網 > PDF目錄30771 > LTC4095EDC#TRM (LINEAR TECHNOLOGY CORP) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 PDF資料下載
參數資料
| 型號： | LTC4095EDC#TRM |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| 封裝： | 2 X 2 MM, 0.75 MM HEIGHT, PLASTIC, DFN-8 |
| 文件頁數： | 15/16頁 |
| 文件大?。?/td> | 225K |
| 代理商： | LTC4095EDC#TRM |
LTC4095
8
4095fa
OPERATION
Charge Cycle Overview
When a battery charge cycle begins, the battery charger
rst determines if the battery is deeply discharged. If the
battery voltage is below VTRKL, typically 2.9V, an automatic
trickle charge feature sets the battery charge current to
10% of the full-scale value.
Once the battery voltage is above 2.9V, the battery charger
begins charging in constant-current mode. When the bat-
tery voltage approaches the 4.2V required to maintain a full
charge, otherwise known as the oat voltage, the charge
current begins to decrease as the LTC4095 switches into
constant-voltage mode.
Trickle Charge and Defective Battery Detection
Any time the battery voltage is below VTRKL, the charger
goes into trickle charge mode and reduces the charge
current to 10% of the full-scale current. If the battery
voltage remains below VTRKL for more than 1/2 hour, the
charger latches the bad-battery state, automatically termi-
nates, and indicates via the CHRG pin that the battery was
unresponsive. If for any reason the battery voltage rises
above VTRKL, the charger will resume charging. Since the
charger has latched the bad-battery state, if the battery
voltage then falls below VTRKL again but without rising past
VRECHRG rst, the charger will immediately assume that
the battery is defective. To reset the charger (i.e., when
the dead battery is replaced with a new battery), simply
remove the input voltage and reapply it or put the part in
and out of suspend mode.
Charge Termination
The battery charger has a built-in safety timer that sets
the total charge time for 4 hours. Once the battery voltage
rises above VRECHRG (typically 4.105V) and the charger
enters constant-voltage mode, the 4-hour timer is started.
After the safety timer expires, charging of the battery will
discontinue and no more current will be delivered.
Automatic Recharge
After the battery charger terminates, it will remain off,
drawing only microamperes of current from the battery.
If the portable product remains in this state long enough,
the battery will eventually self discharge. To ensure that the
battery is always topped off, a charge cycle will automati-
cally begin when the battery voltage falls below VRECHRG
(typically 4.105V). In the event that the safety timer is
running when the battery voltage falls below VRECHRG, it
will reset back to zero. To prevent brief excursions below
VRECHRG from resetting the safety timer, the battery voltage
must be below VRECHRG for more than 1.7ms. The charge
cycle and safety timer will also restart if the IN UVLO or
DUVLO cycles low and then high (e.g., IN is removed
and then replaced) or the charger enters and then exits
suspend mode.
Programming Charge Current
The PROG pin serves both as a charge current program
pin, and as a charge current monitor pin. By design, the
PROG pin current is 1/800th of the battery charge current.
Therefore, connecting a resistor from PROG to ground
programs the charge current while measuring the PROG pin
voltage allows the user to calculate the charge current.
Full-scale charge current is dened as 100% of the con-
stant-current mode charge current programmed by the
PROG resistor. In constant-current mode, the PROG pin
servos to 1V if HPWR is high, which corresponds to charg-
ing at the full-scale charge current, or 200mV if HPWR
is low, which corresponds to charging at 20% of the full-
scale charge current. Thus, the full-scale charge current
and desired program resistor for a given full-scale charge
current are calculated using the following equations:
I
V
R
V
I
CHG
PROG
CHG
=
800
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4099EPDC#TRPBF | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQCC20 |
| LTC4099EUDC#TRPBF | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQCC20 |
| LTC4217CDHC-12#PBF | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO16 |
| LTC4217IFE | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO20 |
| LTC4217CFE#TRPBF | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4096 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Input Standalone Li-Ion Battery Chargers |
| LTC4096EDD | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Input Standalone Li-Ion Battery Chargers |
| LTC4096EDD#PBF | 功能描述:IC CHARGER LI-ION DL 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC4096EDD#TRPBF | 功能描述:IC CHARGER LI-ION DL 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC4096X | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Input Standalone Li-Ion Battery Chargers |
發布緊急采購，3分鐘左右您將得到回復。