- 您現在的位置：買賣IC網 > PDF目錄30771 > LTC4000IUFD#TRPBF (LINEAR TECHNOLOGY CORP) 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQCC28 PDF資料下載
參數資料
| 型號： | LTC4000IUFD#TRPBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQCC28 |
| 封裝： | 4 X 5 MM, LEAD FREE, PLASTIC, MO-220WXXX-X, QFN-28 |
| 文件頁數： | 16/40頁 |
| 文件大?。?/td> | 428K |
| 代理商： | LTC4000IUFD#TRPBF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
LTC4000
23
4000f
applicaTions inForMaTion
The value of R3 and RD can now be set according to the
following formula:
R3 =
RNTC at cold_ threshold – RNTC at hot_ threshold
2.461
RD = 0.219 RNTC at cold_ threshold –
1.219 RNTC at hot_ threshold
Note the important caveat that this method can only be
used to desensitize the thermal effect on the thermistor
and hence push the hot and cold temperature thresholds
apart from each other. When using the formulas above,
if the user finds that a negative value is needed for RD,
the two temperature thresholds selected are too close to
each other and a higher sensitivity thermistor is needed.
For example, this method can be used to set the hot
and cold thresholds independently to 60°C and –5°C.
Using a Vishay Curve 2 thermistor whose nominal value
at 25°C is 100k, the formula results in R3 = 130k and
RD = 41.2k for the closest 1% resistors values.
To increase thermal sensitivity such that the valid charging
temperature band is much smaller than 40°C, it is pos-
sible to put a PTC (positive thermal coefficient) resistor
in series with R3 between the BIAS pin and the NTC pin.
This PTC resistor also needs to be thermally coupled with
the battery. Note that this method increases the number of
thermal sensing connections to the battery pack from one
wire to three wires. The exact value of the nominal PTC
resistor required can be calculated using a similar method
as described above, keeping in mind that the threshold at
the NTC pin is always 75% and 35% of VBIAS.
Leaving the NTC pin floating or connecting it to a capacitor
disables all NTC functionality.
The FLT and CHRG Indicator Pins
The FLT and CHRG pins in the LTC4000 provide status
indicators. Table 2 summarizes the mapping of the pin
states to the part status.
Table 2. FLT and CHRG Status Indicator
FLT
CHRG STATUS
0
NTC Over Ranged – Charging Paused
1
0
Charging Normally
0
1
Charging Terminated and Bad Battery Detected
1
VIBMON < (VC/X – 10mV)
where 1 indicates a high impedance state and 0 indicates
a low impedance pull-down state.
Note that VIBMON < (VCX – 10mV) corresponds to charge
termination only if the C/X termination is selected. If the
charger timer termination is selected, constant voltage
charging may continue for the remaining charger timer
period even after the indicator pins indicate that VIBMON
< (VCX – 10mV). This is also true when no termination is
selected,constantvoltagechargingwillcontinueevenafter
the indicator pins indicate that VIBMON < (VCX – 10mV).
The BIAS Pin
For ease of use the LTC4000 provides a low dropout volt-
age regulator output on the BIAS pin. Designed to provide
up to 0.5mA of current at 2.9V, this pin requires at least
470nF of low ESR bypass capacitance for stability.
Use the BIAS pin as the pull-up source for the NTC resis-
tor networks, since the internal reference for the NTC
circuitry is based on a ratio of the voltage on the BIAS
pin. Furthermore, various 100k pull-up resistors can be
conveniently connected to the BIAS pin.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4075XEDD | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| LTC4075XEDD#PBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| LTC4095EDC#TR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| LTC4095EDC | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| LTC4095EDC#TRM | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4001 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:2A Synchronous Buck Li-Ion Charger |
| LTC4001-1 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:2A Synchronous Buck Li-Ion Charger |
| LTC4001EUF | 制造商:Linear Technology 功能描述:Battery Charger Li-Ion/Li-Pol 2000mA 4.2V 16-Pin QFN EP |
| LTC4001EUF#PBF | 功能描述:IC CHARGER LI-ION BUCK 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
| LTC4001EUF#TRPBF | 功能描述:IC CHARGER LI-ION BUCK 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。