- 您現在的位置：買賣IC網 > PDF目錄98003 > LTC3853EUJ (LINEAR TECHNOLOGY CORP) 0.15 A DUAL SWITCHING CONTROLLER, 830 kHz SWITCHING FREQ-MAX, PQCC40 PDF資料下載
參數資料
| 型號： | LTC3853EUJ |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.15 A DUAL SWITCHING CONTROLLER, 830 kHz SWITCHING FREQ-MAX, PQCC40 |
| 封裝： | 6 X 6 MM, PLASTIC, QFN-40 |
| 文件頁數： | 8/36頁 |
| 文件大?。?/td> | 1780K |
| 代理商： | LTC3853EUJ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
LTC3853
16
3853fa
To ensure that the application will deliver full load cur-
rent over the full operating temperature range, choose
the minimum value for the Maximum Current Sense
Threshold (VSENSE(MAX)) in the Electrical Characteristics
table (22mV, 42mV, or 65mV, depending on the state of
the ILIM pin).
Next, determine the DCR of the inductor. Where provided,
use the manufacturer’s maximum value, usually given
at 20°C. Increase this value to account for the tempera-
ture coefficient of resistance, which is approximately
0.4%/°C. A conservative value for TL(MAX) is 100°C.
To scale the maximum inductor DCR to the desired sense
resistor value, use the divider ratio:
RD =
RSENSE(EQUIV)
DCR(MAX) at TL(MAX)
C1 is usually selected to be in the range of 0.047F to
0.47F. This forces R1||R2 to around 2kΩ, reducing error
that might have been caused by the SENSE pins’ ±1A
current.
The equivalent resistance R1||R2 is scaled to the room
temperature inductance and maximum DCR:
R1|| R2
=
L
(DCR at 20
°C) C1
The sense resistor values are:
R1
=
R1|| R2
RD
; R2
=
R1 RD
1
RD
The maximum power loss in R1 is related to duty cycle,
and will occur in continuous mode at the maximum input
voltage:
PLOSS R1=
VIN(MAX) VOUT
(
)VOUT
R1
Ensure that R1 has a power rating higher than this value.
If high efficiency is necessary at light loads, consider this
power loss when deciding whether to use DCR sensing or
sense resistors. Light load power loss can be modestly
higher with a DCR network than with a sense resistor,
due to the extra switching losses incurred through R1.
However,DCRsensingeliminatesasenseresistor,reduces
conduction losses and provides higher efficiency at heavy
loads.Peakefficiencyisaboutthesamewitheithermethod.
To maintain a good signal-to-noise ratio for the current
sense signal, use a minimum
DVSENSE of 10mV to 15mV.
For a DCR sensing application, the actual ripple voltage
will be determined by:
VSENSE =
VIN – VOUT
R1 C1
VOUT
VIN fOSC
Slope Compensation and Inductor Peak Current
Slope compensation provides stability in constant-
frequency architectures by preventing subharmonic
oscillations at high duty cycles. It is accomplished
internally by adding a compensating ramp to the inductor
current signal at duty cycles in excess of 40%. Normally,
this results in a reduction of maximum inductor peak cur-
rent for duty cycles >40%. However, the LTC3853 uses
a patented scheme that counteracts this compensating
ramp, which allows the maximum inductor peak current
to remain unaffected throughout all duty cycles.
Inductor Value Calculation
Given the desired input and output voltages, the inductor
value and operating frequency, fOSC, directly determine
the inductor’s peak-to-peak ripple current:
IRIPPLE =
VOUT
VIN
VIN – VOUT
fOSC L
Lower ripple current reduces core losses in the inductor,
ESR losses in the output capacitors, and output voltage
ripple. Thus, highest efficiency operation is obtained at
low frequency with a small ripple current. Achieving this,
however, requires a large inductor.
A reasonable starting point is to choose a ripple current
that is about 40% of IOUT(MAX). Note that the largest ripple
current occurs at the highest input voltage. To guarantee
that ripple current does not exceed a specified maximum,
the inductor should be chosen according to:
L
≥
VIN – VOUT
fOSC IRIPPLE
VOUT
VIN
APPLICATIONS INFORMATION
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4011EFE#PBF | BATTERY CHARGE CONTROLLER, 615 kHz SWITCHING FREQ-MAX, PDSO20 |
| LTC4075HVXEDD#TR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| LTC4075HVXEDD | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| LTC4080EMSE | 0.8 A BATTERY CHARGE CONTROLLER, 2750 kHz SWITCHING FREQ-MAX, PDSO10 |
| LTC4085EDE-3#TRPBF | POWER SUPPLY MANAGEMENT CKT, PDSO14 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3853EUJ#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 40-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:PolyPhase® 特色產品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 標準包裝:1 系列:PowerWise® PWM 型:電壓模式 輸出數:1 頻率 - 最大:1MHz 占空比:81% 電源電壓:4.5 V ~ 18 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-5°C ~ 125°C 封裝/外殼:32-WFQFN 裸露焊盤 包裝:Digi-Reel® 產品目錄頁面:1303 (CN2011-ZH PDF) 其它名稱:LM3754SQDKR |
| LTC3853EUJ#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 40-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:PolyPhase® 特色產品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 標準包裝:1 系列:PowerWise® PWM 型:電壓模式 輸出數:1 頻率 - 最大:1MHz 占空比:81% 電源電壓:4.5 V ~ 18 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-5°C ~ 125°C 封裝/外殼:32-WFQFN 裸露焊盤 包裝:Digi-Reel® 產品目錄頁面:1303 (CN2011-ZH PDF) 其它名稱:LM3754SQDKR |
| LTC3853EUJPBF | 制造商:Linear Technology 功能描述:DC-DC Controller Triple Buck 24V QFN40 |
| LTC3853IUJ#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 40-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:PolyPhase® 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LTC3853IUJ#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 40-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:PolyPhase® 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
發布緊急采購，3分鐘左右您將得到回復。