- 您現在的位置：買賣IC網 > PDF目錄377776 > LTC3770 (Linear Technology Corporation) Synchronous Controller with Margining, Tracking and PLL PDF資料下載
參數資料
| 型號： | LTC3770 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Synchronous Controller with Margining, Tracking and PLL |
| 中文描述： | 同步控制器裕，跟蹤和PLL |
| 文件頁數： | 11/24頁 |
| 文件大?。?/td> | 302K |
| 代理商： | LTC3770 |
11
LTC3770
3770f
The basic LTC
3770
application circuit is shown in
Figure 12. External component selection is primarily de-
termined by the maximum load current and begins with
the selection of the sense resistance and power MOSFET
switches. The LTC
3770
uses either a sense resistor or the
on-resistance of the synchronous power MOSFET for
determining the inductor current. The desired amount of
ripple current and operating frequency largely deter-
mines the inductor value. Finally, C
IN
is selected for its
ability to handle the large RMS current into the converter
and C
OUT
is chosen with low enough ESR to meet the
output voltage ripple and transient specification.
Maximum Sense Voltage and V
RNG
Pin
Inductor current is determined by measuring the voltage
across a sense resistance that appears between the SENSE
–
(PGND on G Package) and SENSE
+
(SW on G Package)
pins. The maximum sense voltage is set by the voltage
applied to the V
RNG
pin and is equal to approximately
(0.133)V
RNG
. The current mode control loop will not allow
the inductor current valleys to exceed (0.133)V
RNG
/R
SENSE
.
In practice, one should allow some margin for variations
in the LTC3770 and external component values and a good
guide for selecting the sense resistance is:
R
V
I
OUT MAX
(
SENSE
RNG
=
10
)
An external resistive divider from INTV
CC
can be used to
set the voltage of the V
RNG
pin between 0.5V and 2V
resulting in nominal sense voltages of 50mV to 200mV.
Additionally, the V
RNG
pin can be tied to SGND or INTV
CC
in which case the nominal sense voltage defaults to 50mV
or 200mV, respectively. The maximum allowed sense
voltage is about 1.33 times this nominal value.
Connecting the SENSE
+
and SENSE
–
Pins
The LTC3770 comes in UH and G packages. The UH
package IC can be used with or without a sense resistor.
When using a sense resistor, place it between the source
of the bottom MOSFET, M2, and PGND. Connect the
SENSE
+
and SENSE
–
pins to the top and bottom of the
sense resistor. Using a sense resistor provides a well
defined current limit, but adds cost and reduces efficiency.
Alternatively, one can eliminate the sense resistor and use
the bottom MOSFET as the current sense element by
simply connecting the SENSE
+
pin to the SW pin and
SENSE
–
pin to PGND. This improves efficiency, but one
must carefully choose the MOSFET on-resistance as dis-
cussed below.
Power MOSFET Selection
The LTC3770 requires two external N-channel power
MOSFETs, one for the top (main) switch and one for the
bottom (synchronous) switch. Important parameters for
the power MOSFETs are the breakdown voltage V
(BR)DSS
,
threshold voltage V
(GS)TH
, on-resistance R
DS(ON)
, reverse
transfer capacitance C
RSS
and maximum current I
DS(MAX)
.
The gate drive voltage is set by the 5V INTV
CC
supply.
Consequently, logic-level threshold MOSFETs must be
used in LTC3770 applications. If the input voltage is
expected to drop below 5V, then sub-logic level threshold
MOSFETs should be considered.
When the bottom MOSFET is used as the current sense
element, particular attention must be paid to its on-
resistance. MOSFET on-resistance is typically specified
with a maximum value R
DS(ON)(MAX)
at 25
°
C. In this case,
additional margin is required to accommodate the rise in
MOSFET on-resistance with temperature:
R
R
DS ON MAX
(
SENSE
ρ
T
)(
)
=
The
ρ
T
term is a normalization factor (unity at 25
°
C)
accounting for the significant variation in on-resistance
Figure 1. R
DS(ON)
vs Temperature
JUNCTION TEMPERATURE (
°
C)
–50
ρ
T
1.0
1.5
150
3770 F01
0.5
0
0
50
100
2.0
APPLICATIU
W
U
U
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3770EG | Synchronous Controller with Margining, Tracking and PLL |
| LTC3770EUH | Synchronous Controller with Margining, Tracking and PLL |
| LTC3776 | 16-Bit Buffer/Driver With 3-State Outputs 48-TVSOP -40 to 85 |
| LTC3776EUF | Dual 2-Phase, No RSENSE Synchronous Controller for DDR/QDR Memory Termination |
| LTC3776EGN | Dual 2-Phase, No RSENSE Synchronous Controller for DDR/QDR Memory Termination |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3770EG | 制造商:Linear Technology 功能描述:LDO Cntrlr SYNC BUCK REG 0.6V to 32V 28-Pin SSOP |
| LTC3770EG#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC3770EG#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC3770EUH#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC3770EUH#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。