- 您現在的位置：買賣IC網 > PDF目錄30770 > LTC3766EUFD#PBF (LINEAR TECHNOLOGY CORP) SWITCHING CONTROLLER, 316 kHz SWITCHING FREQ-MAX, PQCC28 PDF資料下載
參數資料
| 型號： | LTC3766EUFD#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING CONTROLLER, 316 kHz SWITCHING FREQ-MAX, PQCC28 |
| 封裝： | 4 X 5 MM, LEAD FREE, PLASTIC, MO-220, QFN-28 |
| 文件頁數： | 18/60頁 |
| 文件大?。?/td> | 607K |
| 代理商： | LTC3766EUFD#PBF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
LTC3766
25
3766f
APPLICATIONS INFORMATION
the active clamp PMOS, which is a potentially significant
weaknessinmanyactiveclampforwardconverterdesigns.
Since the direct flux limit functionality is implemented
in the LTC3765 on the primary side, there is nothing to
adjust on the secondary side. See the LTC3765 data sheet
for details on using this feature. Note that if the LTC3765
terminates the PG MOSFET on-time prematurely to limit
flux accumulation, the LTC3766 will sense a premature
falling on the SW node. In response, the LTC3766 will
automatically terminate the FG on-time, thereby allowing
the transformer core to reset. A premature falling on the
SW node will also occur whenever the LTC3765 has shut
downforanyreason.Consequently,iftheLTC3766detects
19 consecutive premature SW node falling edges on the
SW pin, it will generate a lock fault and shut down.
Primary-Side Power MOSFET Selection
On the primary side, the peak-to-peak drive levels for
both the N-channel main switch and the P-channel active
clamp switch are determined by the voltage on the VCC
pin of the LTC3765. This voltage is normally provided
through the pulse transformer, and is typically set in the
range of 8.5V to 12V. Note that even in applications where
a logic-level MOSFET may be used on the primary side,
the VCC voltage on the LTC3765 must still be in this range
for proper operation.
Selection of the N-channel MOSFET involves careful
consideration of the requirements for breakdown voltage
(BVDSS) and maximum drain current, while balancing the
losses associated with the on-resistance and parasitic
capacitances. In an active clamp topology, the maximum
drain voltage seen by this MOSFET is approximately:
VDS(PG) = 1.2 VCL(MAX)
whereVCL(MAX)isthemaximumactiveclampvoltagegiven
above in the Active Clamp Capacitor section. The factor
of 1.2 has been added to allow margin for ringing and
ripple on the clamp capacitor. It is important to select the
lowest possible voltage rating for this MOSFET in order
to maximize efficiency. Note that the RC snubber on the
active clamp capacitor (see Figure 10) reduces the peak
voltagestressontheprimary-sideMOSFETwithoutadding
to operating losses. Also, the leakage inductance of the
maintransformeratfullloadcancauseconsiderableripple
on the active clamp capacitor, pushing up the peak voltage
stress seen by the primary-side MOSFET. This ripple can
be reduced by using a larger active clamp capacitor and
a proportionally larger RC snubber capacitor. See Active
Clamp Capacitor section for more information.
Once the required BVDSS of the N-channel MOSFET
is known, choose a MOSFET with the lowest available
on-resistance (RDS,ON) that has been optimized for
switching applications (low QG). In most applications,
the MOSFET will be used at a drain current that is a frac-
tion of the maximum rated current, so this rating is not
normally a consideration. The total losses associated with
the N-channel MOSFET at maximum output current can
be estimated using:
PPG =
NP
NS
VOUT IMAX
( )2
VIN
1
+ δ
( )RDS(ON)
+
NS
NP
VCLIMAXRDRQGDfSW
2VMILLER
+QGTOTVCCfSW
where
δisthetemperaturedependenceoftheon-resistance
and VCL is the active clamp voltage (see Active Clamp Ca-
pacitorsection).RDR(approximately1.7ΩfortheLTC3765)
is the gate drive output resistance at the MOSFET’s miller
plateau voltage, VMILLER. The values of QDG, QGTOT and
VMILLER can be taken from the VGS versus QG curve that
is typically provided in a MOSFET data sheet. QGD is the
change in gate charge (QG) during the region where the
VGS voltage is approximately constant and equal to miller
voltage, VMILLER. The total gate charge (QGTOT) is the
gate charge when VGS = VCC. The three parts in the above
equation represent conduction losses, transition losses
and gate drive losses respectively. Highest efficiency is
obtained by selecting a MOSFET that achieves a balance
between conduction losses and the sum of transition and
gate drive losses. Note that the above equation for PPG
is an approximation that includes assumptions. First, it
is assumed that the turn-on transition losses are rela-
tively small because of the leakage inductance in the main
transformer. Also, it is assumed that the energy stored
in this leakage inductance at primary-switch turn-off is
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3805EDD | SWITCHING CONTROLLER, 700 kHz SWITCHING FREQ-MAX, PDSO10 |
| LTC3805EMSE | SWITCHING CONTROLLER, 700 kHz SWITCHING FREQ-MAX, PDSO10 |
| LTC3805HMSE#TR | SWITCHING CONTROLLER, 700 kHz SWITCHING FREQ-MAX, PDSO10 |
| LTC3805EDD#TR | SWITCHING CONTROLLER, 700 kHz SWITCHING FREQ-MAX, PDSO10 |
| LTC3805EMSE#TR | SWITCHING CONTROLLER, 700 kHz SWITCHING FREQ-MAX, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3766HGN#PBF | 功能描述:IC CONTROLLER SYNCH 28SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:Direct Flux Limit™, PolyPhase® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| LTC3766HGN#TRPBF | 功能描述:IC CONTROLLER SYNCH 28SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:Direct Flux Limit™, PolyPhase® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| LTC3766HUFD#PBF | 功能描述:IC CONTROLLER SYNCH 28QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:Direct Flux Limit™, PolyPhase® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| LTC3766HUFD#TRPBF | 功能描述:IC CONTROLLER SYNCH 28QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:Direct Flux Limit™, PolyPhase® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| LTC3766IGN#PBF | 功能描述:IC CONTROLLER SYNCH 28SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:Direct Flux Limit™, PolyPhase® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。