參數資料
型號： LTC3738CUHF
廠商： LINEAR TECHNOLOGY CORP
元件分類： 穩壓器
英文描述： 3-Phase Buck Controller for Intel VRM9/VRM10 with Active Voltage Positioning
中文描述： 5 A SWITCHING CONTROLLER, 630 kHz SWITCHING FREQ-MAX, PQCC38
封裝： 7 X 5 MM, PLASTIC, M0-220WHKD, QFN-38
文件頁數： 15/32頁
文件大?。?/td> 316K
代理商： LTC3738CUHF
15
LTC3738
3738f
Ferrite designs have very low core loss and are preferred
at high switching frequencies, so design goals can
concentrate on copper loss and preventing saturation.
Ferrite core material saturates “hard,” which means that
inductance collapses abruptly when the peak design
current is exceeded. This results in an abrupt increase in
inductor ripple current and consequent output voltage
ripple. Do not allow the core to saturate!
Power MOSFET and Schottky Diode Selection
At least two external power MOSFETs must be selected for
each of the three output sections: One N-channel MOSFET
for the top (main) switch and one or more N-channel
MOSFET(s) for the bottom (synchronous) switch. The
number, type and “on” resistance of all MOSFETs selected
take into account the voltage step-down ratio as well as the
actual position (main or synchronous) in which the MOSFET
will be used. A much smaller and much lower input
capacitance MOSFET should be used for the top MOSFET
in applications that have an output voltage that is less than
1/3 of the input voltage. In applications where V
IN
>> V
OUT
,
the top MOSFETs’ “on” resistance is normally less impor-
tant for overall efficiency than its input capacitance at
operating frequencies above 300kHz. MOSFET manufac-
turers have designed special purpose devices that provide
reasonably low “on” resistance with significantly reduced
input capacitance for the main switch application in switch-
ing regulators.
The peak-to-peak MOSFET gate drive levels are set by the
voltage, V
CC
, requiring the use of logic-level threshold
MOSFETs in most applications. Pay close attention to the
BV
DSS
specification for the MOSFETs as well; many of the
logic-level MOSFETs are limited to 30V or less.
Selection criteria for the power MOSFETs include the “on”
resistance R
SD(ON)
, input capacitance, input voltage and
maximum output current.
MOSFET input capacitance is a combination of several
components but can be taken from the typical “gate
charge” curve included on most data sheets (Figure 4).
APPLICATIOU
1.0
W
U
U
Figure 3. Normalized Peak Output Current
vs Duty Factor [I
RMS
= 0.3(I
O(P-P)
]
So the number of phases used can be selected to minimize
the output ripple current and therefore the output ripple
voltage at the given input and output voltages. In applica-
tions having a highly varying input voltage, additional
phases will produce the best results.
Accepting larger values of
I
L
allows the use of low
inductances but can result in higher output voltage ripple.
A reasonable starting point for setting ripple current is
I
L
= 0.4(I
OUT
)/N, where N is the number of channels and
I
OUT
is the total load current. Remember, the maximum
I
L
occurs at the maximum input voltage. The individual
inductor ripple currents are constant determined by the
inductor, input and output voltages.
Inductor Core Selection
Once the value for the inductors is known, the type of
inductor must be selected. High efficiency converters
generally cannot afford the core loss found in low cost
powdered iron cores, forcing the use of ferrite, molyper-
malloy or Kool M
μ
cores. Actual core loss is independent
of core size for a fixed inductor value, but it is very
dependent on inductance selected. As inductance in-
creases, core losses go down. Unfortunately, increased
inductance requires more turns of wire and therefore
copper losses will increase.
Kool M
μ
is a registered trademark of Magnetics, Inc.
DUTY FACTOR (V
OUT
/V
IN
)
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
3738 F03
6-PHASE
4-PHASE
3-PHASE
2-PHASE
1-PHASE
O
V
O
/
相關PDF資料
PDF描述
LTC3770 Synchronous Controller with Margining, Tracking and PLL
LTC3770EG Synchronous Controller with Margining, Tracking and PLL
LTC3770EUH Synchronous Controller with Margining, Tracking and PLL
LTC3776 16-Bit Buffer/Driver With 3-State Outputs 48-TVSOP -40 to 85
LTC3776EUF Dual 2-Phase, No RSENSE Synchronous Controller for DDR/QDR Memory Termination
相關代理商/技術參數
參數描述
LTC3738CUHF#PBF 功能描述:IC CTRLR SW REG 3PH STPDWN 38QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件
LTC3738CUHF#TR 功能描述:IC CTRLR SW REG 3PH STPDWN 38QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件
LTC3738CUHF#TRPBF 功能描述:IC CTRLR SW REG 3PH STPDWN 38QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件
LTC-3743KG 制造商:Lite-On Semiconductor Corporation 功能描述:
LTC3765EMSE#PBF 功能描述:IC CTLR GATE DRIVER 16-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:Direct Flux Limit™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*