參數資料
型號： LTC3713
廠商： Linear Technology Corporation
英文描述： Low Input Voltage, High Power, No RSENSE Synchronous Buck DC/DC Controller
中文描述： 低輸入電壓，高功率，無檢測電阻同步降壓DC / DC控制器
文件頁數： 7/24頁
文件大?。?/td> 325K
代理商： LTC3713
7
LTC3713
3713fa
PIU
RUN/SS (Pin 1):
Run Control and Soft-Start Input. A
capacitor to ground at this pin sets the ramp time to full
output current (approximately 3s/
μ
F) and the time delay
for overcurrent latchoff (see Applications Information).
Forcing this pin below 0.8V shuts down the device.
V
ON
(Pin 2):
On-Time Voltage Input. Voltage trip point for
the on-time comparator. Tying this pin to the output
voltage makes the on-time proportional to V
OUT
. The
comparator input defaults to 0.7V when the pin is grounded,
2.4V when the pin is tied to INTV
CC
.
PGOOD (Pin 3):
Power Good Output. Open-drain logic
output that is pulled to ground when the output voltage is
not within
±
7.5% of the regulation point.
V
RNG
(Pin 4):
Sense Voltage Range Input. The voltage at
this pin is ten times the nominal sense voltage at maxi-
mum output current and can be set from 0.5V to 2V by a
resistive divider from INTV
CC
. The nominal sense voltage
defaults to 70mV when this pin is tied to ground, 140mV
when tied to INTV
CC
.
FCB (Pin 5):
Forced Continuous Input. Tie this pin to
ground to force continuous synchronous operation at low
load, to INTV
CC
to enable discontinuous mode operation
at low load or to a resistive divider from a secondary output
when using a secondary winding.
I
TH
(Pin 6):
Current Control Threshold and Error Amplifier
Compensation Point. The current comparator threshold
increases with this control voltage. The voltage ranges
from 0V to 2.4V with 0.8V corresponding to zero sense
voltage (zero current).
SGND (Pins 7, 11):
Signal Ground. All small-signal com-
ponents and compensation components should connect to
this ground, which in turn connects to PGND at one point.
I
ON
(Pin 8):
On-Time Current Input. Tie a resistor from V
IN
to this pin to set the one-shot timer current and thereby set
the switching frequency.
V
FB1
(Pin 9):
Error Amplifier Feedback Input. This pin
connects the error amplifier input to an external resistive
divider from V
OUT
.
SHDN (Pin 10):
Shutdown, Active Low. Tie to 1V or more
to enable boost converter portion of the LTC3713. Ground
to shut down.
V
FB2
(Pin 12):
Boost Converter Feedback. The V
FB2
pin is
connected to INTV
CC
through a resistor divider to set the
voltage on INTV
CC
. Set INTV
CC
voltage according to:
V
INTVCC
= 1.23V(1 + R
F4
/R
F3
)
SW2 (Pin 13):
Boost Converter Switch Pin. Connect
inductor/diode for boost converter portion here. Minimize
trace area at this pin to keep EMI down.
PGND (Pins 14, 19):
Power Ground. Connect these pins
closely to the source of the bottom N-channel MOSFET,
the (–) terminal of C
VCC
and the (–) terminal of C
IN
.
V
IN2
(Pin 15):
Input Supply Pin for Boost Converter
Portion of LTC3713. Must be locally bypassed.
V
IN1
(Pin 16):
Main Input Supply. Decouple this pin to
PGND with an RC filter (1
, 0.1
μ
F).
INTV
CC
(Pin 17):
Internal Regulator Output. The driver and
control circuits are powered from this voltage. Decouple
this pin to power ground with a minimum of 4.7
μ
F low ESR
tantalum or ceramic capacitor.
BG (Pin 18):
Bottom Gate Drive. Drives the gate of the
bottom N-channel MOSFET between ground and INTV
CC
.
SENSE
–
(Pin 20):
Negative Current Sense Comparator
Input. The (–) input to the current comparator is normally
connected to power ground unless using a resistive di-
vider from INTV
CC
(see Applications Information).
SENSE
+
(Pin 21):
Positive Current Sense Comparator
Input. The (+) input to the current comparator is normally
connected to the SW1 node unless using a sense resistor
(see Applications Information).
SW1 (Pin 22):
Switch Node. The (–) terminal of the
bootstrap capacitor C
B
connects here. This pin swings
from a diode voltage drop below ground up to V
IN
.
TG (Pin 23):
Top Gate Drive. Drives the top N-channel
MOSFET with a voltage swing equal to INTV
CC
superim-
posed on the switch node voltage SW1.
BOOST (Pin 24):
Boosted Floating Driver Supply. The (+)
terminal of the bootstrap capacitor C
B
connects here. This
pin swings from a diode voltage drop below INTV
CC
up to
V
IN
+ INTV
CC
.
相關PDF資料
PDF描述
LTC3713EG Low Input Voltage, High Power, No RSENSE Synchronous Buck DC/DC Controller
LTC3714 Intel Compatible, Wide Operating Range, Step-Down Controller with Internal Op Amp
LTC3714EG Intel Compatible, Wide Operating Range, Step-Down Controller with Internal Op Amp
LTC3717 Wide Operating Range, No RSENSE Step-Down Controller for DDR/QDR Memory Termination
LTC3717EGN Wide Operating Range, No RSENSE Step-Down Controller for DDR/QDR Memory Termination
相關代理商/技術參數
參數描述
LTC3713EG 功能描述:IC REG CTRLR BUCK PWM CM 24-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR)
LTC3713EG#PBF 功能描述:IC REG CTRLR BUCK PWM CM 24-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR)
LTC3713EG#TR 功能描述:IC REG CTRLR BUCK PWM CM 24-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR)
LTC3713EG#TRPBF 功能描述:IC REG CTRLR BUCK PWM CM 24-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR)
LTC3714EG 功能描述:IC STP-DWN CNTRLR W/OPAMP 28SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*