- 您現在的位置：買賣IC網 > PDF目錄377775 > LTC3713 (Linear Technology Corporation) Low Input Voltage, High Power, No RSENSE Synchronous Buck DC/DC Controller PDF資料下載
參數資料
| 型號： | LTC3713 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Low Input Voltage, High Power, No RSENSE Synchronous Buck DC/DC Controller |
| 中文描述： | 低輸入電壓，高功率，無檢測電阻同步降壓DC / DC控制器 |
| 文件頁數： | 17/24頁 |
| 文件大?。?/td> | 325K |
| 代理商： | LTC3713 |
17
LTC3713
3713fa
loss. For example, if R
DS(ON)
= 0.01
and R
L
= 0.005
, the
loss will range from 1% up to 10% as the output current
varies from 1A to 10A for a 1.5V output.
2. Transition loss. This loss arises from the brief amount
of time the top MOSFET spends in the saturated region
during switch node transitions. It depends upon the input
voltage, load current, driver strength and MOSFET capaci-
tance, among other factors. The loss is significant at input
voltages above 20V and can be estimated from:
Transition Loss
(1.7A
–1
) V
IN2
I
OUT
C
RSS
f
3. INTV
CC
current. This is the sum of the MOSFET driver
and control currents.
4. C
IN
loss. The input capacitor has the difficult job of
filtering the large RMS input current to the regulator. It
must have a very low ESR to minimize the AC I
2
R loss and
sufficient capacitance to prevent the RMS current from
causing additional upstream losses in fuses or batteries.
Other losses, including C
OUT
ESR loss, Schottky diode D1
conduction loss during dead time and inductor core loss
generally account for less than 2% additional loss.
When making adjustments to improve efficiency, the input
current is the best indicator of changes in efficiency. If you
make a change and the input current decreases, then the
efficiency has increased. If there is no change in input
current, then there is no change in efficiency.
Checking Transient Response
The regulator loop response can be checked by looking
at the load transient response. Switching regulators take
several cycles to respond to a step in load current. When
a load step occurs, V
OUT
immediately shifts by an amount
equal to
I
LOAD
(ESR), where ESR is the effective series
resistance of C
OUT
.
I
LOAD
also begins to charge or
discharge C
OUT
generating a feedback error signal used
by the regulator to return V
OUT
to its steady-state value.
During this recovery time, V
OUT
can be monitored for
overshoot or ringing that would indicate a stability
problem. The I
TH
pin external components shown in
Figure 1 will provide adequate compensation for most
applications. For a detailed explanation of switching
control loop theory see Application Note 76.
Design Example
As a design example, take a supply with the following
specifications: V
IN
= 1.8V to 3.3V, V
OUT
= 1.25V
±
100mV,
I
OUT(MAX)
= 6A, f = 300kHz. First, calculate the timing
resistor with V
ON
= V
OUT
:
R
V
V
10
V
kHz
pF
k
ON
=
=
2 5
)(
–0 7
)
2 5
)(
)
300
240
Next, use a standard value of 237k and choose the inductor
for about 40% ripple current at the maximum V
IN
:
L
V
)0 4 6
kHz
A
V
V
H
=
=
μ
1 25
.
300
(
1
1 25
3 3
.
1 08
.
)
–
.
Selecting a standard value of 1
μ
H results in a maximum
ripple current of:
=
μ
=
I
V
)(
kHz
H
V
V
A
L
1 25
.
300
(
1
1
1 25
3 3
.
2 6
.
)
–
.
Next, choose the synchronous MOSFET switch. Choosing
an IRF7811A (R
DS(ON)
= 0.013
, C
RSS
= 60pF,
θ
JA
=
50
°
C/W) yields a nominal sense voltage of:
V
SNS(NOM)
= (6A)(1.3)(0.013
) = 101.4mV
Tying V
RNG
to 1V will set the current sense voltage range
for a nominal value of 100mV with current limit occurring
at 133mV. To check if the current limit is acceptable,
assume a junction temperature of about 10
°
C above a
50
°
C ambient with
ρ
60
°
C
= 1.15:
I
mV
A
A
LIMIT
≥
+
=
133
)( .
1 15 0 013
1
2
2 6
10 2
)
)
.
and double check the assumed T
J
in the MOSFET:
P
V
V
V
A
W
BOT
=
=
3 3
.
–1 25
.
3 3
10 2
2
1 15 0 013
)( .
0 24
.
2
.
)
T
J
= 50
°
C + (0.24W)(50
°
C/W) = 62
°
C
Now check the power dissipation of the top MOSFET at
current limit with
ρ
80
°
C
= 1.3:
APPLICATIU
W
U
U
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3713EG | Low Input Voltage, High Power, No RSENSE Synchronous Buck DC/DC Controller |
| LTC3714 | Intel Compatible, Wide Operating Range, Step-Down Controller with Internal Op Amp |
| LTC3714EG | Intel Compatible, Wide Operating Range, Step-Down Controller with Internal Op Amp |
| LTC3717 | Wide Operating Range, No RSENSE Step-Down Controller for DDR/QDR Memory Termination |
| LTC3717EGN | Wide Operating Range, No RSENSE Step-Down Controller for DDR/QDR Memory Termination |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3713EG | 功能描述:IC REG CTRLR BUCK PWM CM 24-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC3713EG#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 24-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC3713EG#TR | 功能描述:IC REG CTRLR BUCK PWM CM 24-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC3713EG#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 24-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC3714EG | 功能描述:IC STP-DWN CNTRLR W/OPAMP 28SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。