參數資料
型號: LTC3700EMS#TRPBF
廠商: Linear Technology
文件頁數: 8/16頁
文件大?。?/td> 215K
描述: IC REG DL BUCK/LINEAR 10MSOP
產品培訓模塊: More Information on LDOs
標準包裝: 2,500
拓撲: 降壓(降壓)(1),線性(LDO)(1)
功能: 任何功能
輸出數: 2
頻率 - 開關: 550kHz
電壓/電流 - 輸出 1: 可調至0.8V,5A
電壓/電流 - 輸出 2: 可調至0.8V,150mA
帶 LED 驅動器:
帶監控器:
帶序列發生器:
電源電壓: 2.4 V ~ 9.8 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 10-TFSOP,10-MSOP(0.118",3.00mm 寬)
供應商設備封裝: 10-MSOP
包裝: 帶卷 (TR)
8
LTC3700
3700f
OPERATIO
(Refer to Functional Diagram)
Main Control Loop (Buck Controller)
The LTC3700 is a constant frequency current mode switch-
ing regulator. During normal operation, the external
P-channel power MOSFET is turned on each cycle when
the oscillator sets the RS latch (RS1) and turned off when
the current comparator (ICMP) resets the latch. The peak
inductor current at which ICMP resets the RS latch is
controlled by the voltage on the I
TH
/RUN pin, which is the
output of the error amplifier EAMP. An external resistive
divider connected between V
OUT
 and ground allows the
EAMP to receive an output feedback voltage V
FB
. When the
load current increases, it causes a slight decrease in V
FB
relative to the 0.8V reference, which in turn causes the
I
TH
/RUN voltage to increase until the average inductor
current matches the new load current.
The main control loop is shut down by pulling the I
TH
/RUN
pin low. Releasing I
TH
/RUN allows an internal 0.5礎
current source to charge up the external compensation
network. When the I
TH
/RUN pin reaches 0.3V, the main
control loop is enabled with the I
TH
/RUN voltage then
pulled up to its zero current level of approximately 0.7V.
As the external compensation network continues to charge
up, the corresponding output current trip level follows,
allowing normal operation.
Comparator OVP guards against transient overshoots
>7.5% by turning off the external P-channel power
MOSFET and keeping it off until the fault is removed.
Burst Mode Operation
The buck enters Burst Mode operation at low load cur-
rents. In this mode, the peak current of the inductor is set
as if V
ITH
/RUN = 1V (at low duty cycles) even though the
voltage at the I
TH
/RUN pin is at a lower value. If the
inductors average current is greater than the load require-
ment, the voltage at the I
TH
/RUN pin will drop. When the
I
TH
/RUN voltage goes below 0.85V, the sleep signal goes
high, turning off the external MOSFET. The sleep signal
goes low when the I
TH
/RUN voltage goes above 0.925V
and the buck resumes normal operation. The next oscilla-
tor cycle will turn the external MOSFET on and the switch-
ing cycle repeats.
Dropout Operation
When the input supply voltage decreases towards the
output voltage, the rate of change of inductor current
during the ON cycle decreases. This reduction means that
the external P-channel MOSFET will remain on for more
than one oscillator cycle since the inductor current has not
ramped up to the threshold set by EAMP. Further reduc-
tion in input supply voltage will eventually cause the
P-channel MOSFET to be turned on 100%, i.e., DC. The
output voltage will then be determined by the input voltage
minus the voltage drop across the MOSFET, the sense
resistor and the inductor.
Undervoltage Lockout
To prevent operation of the P-channel MOSFET below safe
input voltage levels, an undervoltage lockout is incorpo-
rated into the buck input supply. When the input supply
voltage drops below approximately 2.1V, the P-channel
MOSFET and all circuitry is turned off except the under-
voltage block, which draws only several microamperes.
Short-Circuit Protection
When the output is shorted to ground, the frequency of the
oscillator will be reduced to about 110kHz. This lower
frequency allows the inductor current to safely discharge,
thereby preventing current runaway. The oscillators fre-
quency will gradually increase to its designed rate when
the feedback voltage again approaches 0.8V.
Overvoltage Protection
As a further protection, the overvoltage comparator in the
buck will turn the external MOSFET off when the feedback
voltage has risen 7.5% above the reference voltage of
0.8V. This comparator has a typical hysteresis of 20mV.
Slope Compensation and Inductors Peak Current
The inductors peak current is determined by:
I
V
R
PK
ITH
SENSE
=
(
)
 .
07
10
相關PDF資料
PDF描述
LTC4151HMS#TRPBF IC PWR MONITOR MS 80V SD 10MSOP
LTC4210-2CS6#TRM IC CONTROLLER HOT SWAP TSOT23-6
LTC4211IMS8 IC CONTROLLER HOT SWAP 8-MSOP
LTC4212IMS#TRPBF IC CTRLR HOTSWAP TIMEOUT 10MSOP
LTC4214-1IMS#TRPBF IC CTRLR HOTSWAP NEGVOLT 10MSOP
相關代理商/技術參數
參數描述
LTC3701EGN 功能描述:IC REG CTRLR BUCK PWM CM 16-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:PolyPhase® 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR)
LTC3701EGN#PBF 功能描述:IC REG CTRLR BUCK PWM CM 16-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:PolyPhase® 特色產品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 標準包裝:1 系列:PowerWise® PWM 型:電壓模式 輸出數:1 頻率 - 最大:1MHz 占空比:81% 電源電壓:4.5 V ~ 18 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-5°C ~ 125°C 封裝/外殼:32-WFQFN 裸露焊盤 包裝:Digi-Reel® 產品目錄頁面:1303 (CN2011-ZH PDF) 其它名稱:LM3754SQDKR
LTC3701EGN#TR 功能描述:IC REG CTRLR BUCK PWM CM 16-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:PolyPhase® 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR)
LTC3701EGN#TRPBF 功能描述:IC REG CTRLR BUCK PWM CM 16-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:PolyPhase® 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR)
LTC3701EGNPBF 制造商:Linear Technology 功能描述:DC-DC Controller Dual Step-Dn 10V SSOP16