參數資料
型號： LTC3586EUFE-1#TRPBF
廠商： LINEAR TECHNOLOGY CORP
元件分類： 穩壓器
英文描述： BATTERY CHARGE CONTROLLER, PQCC38
封裝： 4 X 6 MM, 0.75 MM HEIGHT, LEAD FREE, PLASTIC, QFN-38
文件頁數： 3/36頁
文件大小： 317K
代理商： LTC3586EUFE-1#TRPBF
LTC3586/LTC3586-1
11
3586fa
PIN FUNCTIONS
ILIM0, ILIM1 (Pins 1, 2): Logic Inputs. ILIM0 and ILIM1
control the current limit of the PowerPath switching
regulator. See Table 1.
SW4 (Pin 8): Switch Node for the (Boost) Switching
Regulator 4. An external inductor connects between this
pin and VIN4.
MODE (Pin 9): Digital Input. The MODE pin controls dif-
ferent modes of operation for the switching regulators
according to Table 2.
Table 1. USB Current Limit Settings
(ILIM1)(ILIM0)
USB SETTING
0
1x Mode (USB 100mA Limit)
0
1
10x Mode (Wall 1A Limit)
1
0
Suspend
1
5x Mode (USB 500mA Limit)
LDO3V3 (Pin 3): 3.3V LDO Output Pin. This pin provides
a regulated always-on 3.3V supply voltage. LDO3V3
gets its power from VOUT. It may be used for light loads
such as a watch dog microprocessor or real time clock.
A 1μF capacitor is required from LDO3V3 to ground. If
the LDO3V3 output is not used it should be disabled by
connecting it to VOUT.
CLPROG (Pin 4): USB Current Limit Program and Moni-
tor Pin. A resistor from CLPROG to ground determines
the upper limit of the current drawn from the VBUS pin.
A fraction of the VBUS current is sent to the CLPROG pin
when the synchronous switch of the PowerPath switching
regulator is on. The switching regulator delivers power until
the CLPROG pin reaches 1.188V. Several VBUS current limit
settings are available via user input which will typically
correspond to the 500mA and 100mA USB specications.
A multilayer ceramic averaging capacitor is required at
CLPROG for ltering.
NTC (Pin 5): Input to the Thermistor Monitoring Circuits.
The NTC pin connects to a battery’s thermistor to deter-
mine if the battery is too hot or too cold to charge. If the
battery’s temperature is out of range, charging is paused
until it re-enters the valid range. A low drift bias resistor
is required from VBUS to NTC and a thermistor is required
from NTC to ground. If the NTC function is not desired,
the NTC pin should be grounded.
VOUT4 (Pins 6, 7): Power Output for the (Boost) Switching
Regulator 4. A 10μF MLCC capacitor should be placed as
close to the pins as possible.
Table 2. Switching Regulators Mode
REGULATION MODE
Mode
Buck
Buck-Boost
Boost
0
Pulse-Skip
PWM
Pulse-Skip
1
Burst
Pulse-Skip
FB4 (Pin 10): Feedback Input for the (Boost) Switching
Regulator 4. When the control loop is complete, the volt-
age on this pin servos to 0.8V.
FB3 (Pin 11): Feedback Input for (Buck-Boost) Switching
Regulator 3. When regulator 3’s control loop is complete,
this pin servos to 0.8V.
VC3(Pin12):OutputoftheErrorAmplierandVoltageCom-
pensation Node for (Buck-Boost) Switching Regulator 3.
External Type I or Type III compensation (to FB3) connects
to this pin. See the Applications Information section for
selecting buck-boost compensation components.
SWAB3 (Pin 13): Switch Node for (Buck-Boost) Switch-
ing Regulator 3. Connected to Internal Power Switches A
and B. An external inductor connects between this node
and SWCD3.
VIN3(Pins14,15):PowerInputfor(Buck-Boost)Switching
Regulator 3. These pins will generally be connected to VOUT.
A 1μF MLCC capacitor is recommended on these pins.
VOUT3 (Pins 16, 17): Output Voltage for (Buck-Boost)
Switching Regulator 3.
EN3 (Pin 18): Digital Input. This input enables the
buck-boost switching regulator 3.
SWCD3 (Pin 19): Switch Node for (Buck-Boost) Switch-
ing Regulator 3 Connected to Internal Power Switches C
and D. An external inductor connects between this node
and SWAB3.
相關PDF資料
PDF描述
LTC3672BEDC-1#PBF 1.1 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO8
LTC3728LZEUH 3 A DUAL SWITCHING CONTROLLER, 590 kHz SWITCHING FREQ-MAX, PQCC28
LTC3773EUHF SWITCHING CONTROLLER, 700 kHz SWITCHING FREQ-MAX, PQCC38
LTC3773EG SWITCHING CONTROLLER, 700 kHz SWITCHING FREQ-MAX, PDSO36
LTC3801ES6#PBF 1 A SWITCHING CONTROLLER, 650 kHz SWITCHING FREQ-MAX, PDSO6
相關代理商/技術參數
參數描述
LTC3586EUFE-2#PBF 功能描述:IC USB POWER MANAGER HE 38-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:Bat-Track™, PowerPath™ 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP（4x4） 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR
LTC3586EUFE-2#TRPBF 功能描述:IC USB POWER MANAGER HE 38-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:Bat-Track™, PowerPath™ 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP（4x4） 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR
LTC3586EUFE-3#PBF 功能描述:IC USB POWER MANAGER HE 38-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:Bat-Track™, PowerPath™ 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP（4x4） 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR
LTC3586EUFE-3#TRPBF 功能描述:IC USB POWER MANAGER HE 38-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:Bat-Track™, PowerPath™ 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP（4x4） 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR
LTC3586EUFE-PBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Effi ciency USB Power Manager with Boost, Buck-Boost and Dual Bucks
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*