- 您現在的位置：買賣IC網 > PDF目錄377775 > LTC3413EFE (LINEAR TECHNOLOGY CORP) 3A, 2MHz Monolithic Synchronous Regulator for DDR/QDR Memory Termination PDF資料下載
參數資料
| 型號： | LTC3413EFE |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 3A, 2MHz Monolithic Synchronous Regulator for DDR/QDR Memory Termination |
| 中文描述： | 7.2 A SWITCHING REGULATOR, 2000 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | 4.40 MM, PLASTIC, TSSOP-16 |
| 文件頁數： | 8/16頁 |
| 文件大小： | 243K |
| 代理商： | LTC3413EFE |
8
LTC3413
sn3413 3413fs
APPLICATIOU
Table 1 shows some recommended surface mount
inductors for LTC3413 applications.
W
U
U
The output ripple is highest at maximum input voltage
since
I
L
increases with input voltage. Multiple capacitors
placed in parallel may be needed to meet the ESR and RMS
current handling requirements. Dry tantalum, special poly-
mer, aluminum electrolytic and ceramic capacitors are all
available in surface mount packages. Special polymer
capacitors offer very low ESR but have lower capacitance
density than other types. Tantalum capacitors have the
highest capacitance density but it is important to only use
types that have been surge tested for use in switching
power supplies.
Aluminum electrolytic capacitors have significantly higher
ESR, but can be used in cost-sensitive applications pro-
vided that consideration is given to ripple current ratings
and long term reliability. Ceramic capacitors have excel-
lent low ESR characteristics but can have a high voltage
coefficient and audible piezoelectric effects. The high Q of
ceramic capacitors with trace inductance can also lead to
significant ringing.
Using Ceramic Input and Output Capacitors
Higher values, lower cost ceramic capacitors are now
becoming available in smaller case sizes. Their high ripple
current, high voltage rating and low ESR make them ideal
for switching regulator applications. However, care must
be taken when these capacitors are used at the input and
output. When a ceramic capacitor is used at the input and
the power is supplied by a wall adapter through long wires,
a load step at the output can induce ringing at the input,
V
IN
. At best, this ringing can couple to the output and be
mistaken as loop instability. At worst, a sudden inrush of
current through the long wires can potentially cause a
voltage spike at V
IN
large enough to damage the part.
When choosing the input and output ceramic capacitors,
choose the X5R or X7R dielectric formulations. These
Table 1. Recommended Surface Mount Inductors
Value
(
μ
H)
0.47
0.47
0.44
0.47
DCR
(m
)
13.0
4.2
6.0
20.0
Manufacturer
Murata
Vishay/Dale
Pulse
Cooper
Part Number
LQH55DNR47M01
IHLP2525CZPJR47M01
P1166.681T
SD20-R47
C
IN
and C
OUT
Selection
The input capacitance, C
IN
, is needed to filter the trapezoi-
dal wave current at the source of the top MOSFET. To
prevent large voltage transients from occurring, a low ESR
input capacitor sized for the maximum RMS current
should be used. The maximum RMS current is given by:
I
I
V
V
V
V
RMS
OUT MAX
(
OUT
IN
IN
OUT
=
)
–1
This formula has a maximum at V
IN
= 2V
OUT
, where I
RMS
= I
OUT
/2. This simple worst-case condition is commonly
used for design because even significant deviations do not
offer much relief. Note that ripple current ratings from
capacitor manufacturers are often based on only 2000
hours of life which makes it advisable to further derate the
capacitor, or choose a capacitor rated at a higher tempera-
ture than required. Several capacitors may also be paral-
leled to meet size or height requirements in the design.
The selection of C
OUT
is determined by the effective series
resistance (ESR) that is required to minimize voltage
ripple and load step transients as well as the amount of
bulk capacitance that is necessary to ensure that the
control loop is stable. Loop stability can be checked by
viewing the load transient response as described in a later
section. The output ripple,
V
OUT
, is determined by:
≤
+
V
I ESR
fC
OUT
OUT
1
8
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3423 | Low Output Voltage 3MHz Micropower Synchronous Boost Converters |
| LTC3423EMS | Low Output Voltage 3MHz Micropower Synchronous Boost Converters |
| LTC3424 | Low Output Voltage 3MHz Micropower Synchronous Boost Converters |
| LTC3424EMS | Low Output Voltage 3MHz Micropower Synchronous Boost Converters |
| LTC3442 | Micropower Synchronous Buck-Boost DC/DC Converter with Automatic Burst Mode Operation |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3413EFE#PBF | 功能描述:IC REG BUCK SYNC ADJ 3A 16TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
| LTC3413EFE#TR | 功能描述:IC REG BUCK SYNC ADJ 3A 16TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LTC3413EFE#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 3A 16TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LTC3413EFEPBF | 制造商:Linear Technology 功能描述: 制造商:Linear Technology 功能描述:3A 2MHz Reg. for DDR Termination TSSOP16 |
| LTC3413EFE-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:3A, 2MHz Monolithic Synchronous Regulator for DDR/QDR Memory Termination |
發布緊急采購，3分鐘左右您將得到回復。