- 您現在的位置：買賣IC網 > PDF目錄377775 > LTC3411 (Linear Technology Corporation) 1.25A, 4MHz, Synchronous Step-Down DC/DC Converter PDF資料下載
參數資料
| 型號： | LTC3411 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | 1.25A, 4MHz, Synchronous Step-Down DC/DC Converter |
| 中文描述： | 電流1.25A，4MHz，同步降壓型DC / DC轉換器 |
| 文件頁數： | 13/20頁 |
| 文件大?。?/td> | 288K |
| 代理商： | LTC3411 |
LTC3411
13
sn3411 3411fs
The output voltage settling behavior is related to the
stability of the closed-loop system and will demonstrate
the actual overall supply performance. For a detailed
explanation of optimizing the compensation components,
including a review of control loop theory, refer to Linear
Technology Application Note 76.
Although a buck regulator is capable of providing the full
output current in dropout, it should be noted that as the
input voltage V
IN
drops toward V
OUT
, the load step capa-
bility does decrease due to the decreasing voltage across
the inductor. Applications that require large load step
capability near dropout should use a different topology
such as SEPIC, Zeta or single inductor, positive buck/
boost.
In some applications, a more severe transient can be
caused by switching in loads with large (>1uF) input
capacitors. The discharged input capacitors are effectively
put in parallel with C
OUT
, causing a rapid drop in V
OUT
. No
regulator can deliver enough current to prevent this prob-
lem, if the switch connecting the load has low resistance
and is driven quickly. The solution is to limit the turn-on
speed of the load switch driver. A hot swap controller is
designed specifically for this purpose and usually incorpo-
rates current limiting, short-circuit protection, and soft-
starting.
Efficiency Considerations
The percent efficiency of a switching regulator is equal to
the output power divided by the input power times 100%.
It is often useful to analyze individual losses to determine
what is limiting the efficiency and which change would
produce the most improvement. Percent efficiency can be
expressed as:
%Efficiency = 100% – (L1 + L2 + L3 + ...)
where L1, L2, etc. are the individual losses as a percentage
of input power.
Although all dissipative elements in the circuit produce
losses, four main sources usually account for most of the
losses in LTC3411 circuits: 1) LTC3411 V
IN
current,
2)switching losses, 3) I
2
R losses, 4) other losses.
1) The V
IN
current is the DC supply current given in the
electrical characteristics which excludes MOSFET driver
and control currents. V
IN
current results in a small (<0.1%)
loss that increases with V
IN
, even at no load.
2) The switching current is the sum of the MOSFET driver
and control currents. The MOSFET driver current results
from switching the gate capacitance of the power MOSFETs.
Each time a MOSFET gate is switched from low to high to
low again, a packet of charge dQ moves from V
IN
to
ground. The resulting dQ/dt is a current out of V
IN
that is
typically much larger than the DC bias current. In continu-
ous mode, I
GATECHG
= f
O
(QT + QB), where QT and QB are
the gate charges of the internal top and bottom MOSFET
switches. The gate charge losses are proportional to V
IN
and thus their effects will be more pronounced at higher
supply voltages.
3) I
2
R Losses are calculated from the DC resistances of the
internal switches, R
SW
, and external inductor, RL. In
continuous mode, the average output current flowing
through inductor L but is “chopped” between the internal
top and bottom switches. Thus, the series resistance
looking into the SW pin is a function of both top and
bottom MOSFET R
DS(ON)
and the duty cycle (DC) as
follows:
R
SW
= (R
DS(ON)
TOP)(DC) + (R
DS(ON)
BOT)(1 – DC)
The R
DS(ON)
for both the top and bottom MOSFETs can be
obtained from the Typical Performance Characteristics
curves. Thus, to obtain I
2
R losses:
I
2
R losses = I
OUT
2(R
SW
+ RL)
4) Other “hidden” losses such as copper trace and internal
battery resistances can account for additional efficiency
degradations in portable systems. It is very important to
include these “system” level losses in the design of a
system. The internal battery and fuse resistance losses
can be minimized by making sure that C
IN
has adequate
charge storage and very low ESR at the switching fre-
quency. Other losses including diode conduction losses
during dead-time and inductor core losses generally ac-
count for less than 2% total additional loss.
APPLICATIU
W
U
U
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3411EDD | 1.25A, 4MHz, Synchronous Step-Down DC/DC Converter |
| LTC3413 | 3A, 2MHz Monolithic Synchronous Regulator for DDR/QDR Memory Termination |
| LTC3413EFE | 3A, 2MHz Monolithic Synchronous Regulator for DDR/QDR Memory Termination |
| LTC3423 | Low Output Voltage 3MHz Micropower Synchronous Boost Converters |
| LTC3423EMS | Low Output Voltage 3MHz Micropower Synchronous Boost Converters |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3411A | 制造商:LINER 制造商全稱:Linear Technology 功能描述:1.25A, 4MHz, Synchronous Step-Down DC/DC Converter |
| LTC3411AEDD#PBF | 功能描述:IC REG BUCK SYNC ADJ 1.25A 10DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:1.24 V ~ 30 V 輸入電壓:1.5 V ~ 12 V PWM 型:電流模式，混合 頻率 - 開關:600kHz 電流 - 輸出:500mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:8-SOIC |
| LTC3411AEDD#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 1.25A 10DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:1.24 V ~ 30 V 輸入電壓:1.5 V ~ 12 V PWM 型:電流模式，混合 頻率 - 開關:600kHz 電流 - 輸出:500mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:8-SOIC |
| LTC3411AEDD-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:1.25A, 4MHz, Synchronous Step-Down DC/DC Converter |
| LTC3411AEDD-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:1.25A, 4MHz, Synchronous Step-Down DC/DC Converter |
發布緊急采購，3分鐘左右您將得到回復。