- 您現在的位置：買賣IC網 > PDF目錄30769 > LTC2941IDCB#TRPBF (LINEAR TECHNOLOGY CORP) POWER SUPPLY SUPPORT CKT, PDSO6 PDF資料下載
參數資料
| 型號： | LTC2941IDCB#TRPBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | POWER SUPPLY SUPPORT CKT, PDSO6 |
| 封裝： | 2 X 3 MM, LEAD FREE, PLASTIC, MO-229, DFN-6 |
| 文件頁數： | 15/16頁 |
| 文件大?。?/td> | 199K |
| 代理商： | LTC2941IDCB#TRPBF |
LTC2941
8
2941fa
applicaTions inFormaTion
Bit A[5] is set if the LTC2941’s accumulated charge over-
flowsorunderflowsthecombinedtotalinregistersCandD.
Notethatthecountingprocessdoesnotrollover,butsimply
stops at FFFFh or 0000h until the direction is reversed.
The LTC2941 includes a battery undervoltage monitor,
whichsetsbitA1ifthelimitisexceeded.Limitsareselected
in the control register.
The undervoltage lockout (UVLO) bit A[0] is set if, dur-
ing operation, the voltage on SENSE+ drops below 2.7V
without reaching the POR level. The analog parts of the
coulomb counter are switched off while the digital register
values are retained. After recovery of the supply voltage
the coulomb counter resumes integrating with the stored
value in the accumulated charge registers (C, D) but it has
missed any charge flowing while VSENSE+ < 2.7V.
The hard coded bit A[7] of the status register enables the
host to distinguish the LTC2941 from the pin compatible
LTC2942, allowing the same software to be used with
both devices.
Control Register (B)
The operation of the LTC2941 can be controlled by pro-
gramming the control register at address 01h. Table 3
shows the organization of the 8-bit control register B[7:0]
Table 3. Control Register B
BIT NAME
OPERATION
DEFAULT
B[7:6] VBAT Alert
[11] Threshold Value = 3.0V.
[10] Threshold Value = 2.9V.
[01] Threshold Value = 2.8V.
[00] VBAT Alert Off.
[00]
B[5:3] Prescaler M Sets coulomb counter prescaling
factor M between 1 and 128.
Default is 128.
M = 2(4 B[5] + 2 B[4] + B[3]).
[111]
B[2:1] AL/CC
Configure
Configures the AL/CC pin.
[10] Alert Mode.
Alert functionality enabled.
Pin becomes logic output.
[01] Charge Complete Mode.
Pin becomes logic input and accepts
“charge complete” signal (e.g., from
a charger) to set accumulated charge
Register to FFFFh.
[00] AL/CC pin disabled.
[11] Not allowed.
[10]
B[0] Shutdown
Shut down analog section to reduce
ISUPPLY.
[0]
Power Down B[0]
Programming the last bit B[0] of the control register to 1
sets the analog parts of the LTC2941 in power down and
the current consumption drops typically below 1A. All
analogcircuitsaredisabledwhilethevaluesintheregisters
are retained. Note that any charge flowing while B[0] is 1
is not measured and the charge information below 1 LSB
of the accumulated charge register is lost.
Alert/Charge Complete Configuration B[2:1]
The AL/CC pin is a dual function pin configured by the
control register. By setting bits B[2:1] to [10] (default)
the AL/CC pin is configured as an alert pin following the
SMBusprotocol.InthisalertmodetheAL/CCpinisadigital
output and is pulled low if one of the measured quantities
exceeds its high or low threshold or if the an overflow/
underflow occurs in the accumulated charge registers C
and D. An alert response procedure started by the master
resets the alert at the AL/CC pin. For further information
see the Alert Response Protocol section.
Setting the control bits B[2:1] to [01] configures the AL/
CC pin as a digital input. In this mode, a high input on the
AL/CC pin communicates to the LTC2941 that the battery
is full and the accumulated charge is set to its maximum
value FFFFh. The AL/CC pin would typically be connected
to the “charge complete” output from the battery charger
circuitry.
If neither the alert nor the charge complete functionality
is desired, bits B[2:1] should be set to [00]. The AL/CC
pin is then disabled and should be tied to GND. Avoid set-
ting B[2:1] to [11] as it enables the alert and the charge
complete modes simultaneously.
Choosing RSENSE and Coulomb Counter
Prescaler “M” B[5:3]
To achieve the specified precision of the coulomb counter
the differential voltage between SENSE+ and SENSE– must
stay within ±50mV. For differential input signals up to
±300mV the LTC2941 will remain functional but the preci-
sion of the coulomb counter is not guaranteed.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3388EMSE-3#PBF | 0.21 A SWITCHING REGULATOR, PDSO10 |
| LTC3388IDD-3#TRPBF | 0.21 A SWITCHING REGULATOR, PDSO10 |
| LTC3388EDD-3#PBF | 0.21 A SWITCHING REGULATOR, PDSO10 |
| LTC3388IDD-1#PBF | 0.21 A SWITCHING REGULATOR, PDSO10 |
| LTC3388IMSE-1#PBF | 0.21 A SWITCHING REGULATOR, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2942CDCB#PBF | 制造商:Linear Technology 功能描述:IC, BATTERY GAS GAUGE, LI-ION, DFN-6; Battery Management Function:Fuel Gauge; Battery Type:Li-Ion; Supply Voltage Min:2.7V; Supply Voltage Max:5.5V; Battery IC Case Style:DFN; No. of Pins:6; IC Interface Type:I2C ;RoHS Compliant: Yes |
| LTC2942CDCB#TRMPBF | 功能描述:IC FUEL/GAS GAUGE LI-ION 6DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
| LTC2942CDCB#TRPBF | 功能描述:IC FUEL/GAS GAUGE LI-ION 6DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC2942CDCB-1#PBF | 制造商:Linear Technology 功能描述:IC BATTERY FUEL GAUGE LI-ION 5.5V DFN-6 制造商:Linear Technology 功能描述:IC, BATTERY FUEL GAUGE LI-ION 5.5V DFN-6 制造商:Linear Technology 功能描述:IC, BATTERY FUEL GAUGE LI-ION 5.5V DFN-6; Battery Management Function:Fuel Gauge, Charge Controller; Battery Type:Li-Ion; Supply Voltage Min:2.7V; Supply Voltage Max:5.5V; Battery IC Case Style:DFN; No. of Pins:6 ;RoHS Compliant: Yes |
| LTC2942CDCB-1#TRMPBF | 功能描述:IC FUEL/GAS GAUGE LI-ION 1A 6DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
發布緊急采購，3分鐘左右您將得到回復。