- 您現在的位置：買賣IC網 > PDF目錄39420 > LTC2495CUHF#TR (LINEAR TECHNOLOGY CORP) 16-CH 16-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PQCC38 PDF資料下載
參數資料
| 型號： | LTC2495CUHF#TR |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | ADC |
| 英文描述： | 16-CH 16-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PQCC38 |
| 封裝： | 5 X 7 MM, PLASTIC, MO-220WKHD, QFN-38 |
| 文件頁數： | 5/32頁 |
| 文件大小： | 619K |
| 代理商： | LTC2495CUHF#TR |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
LTC2495
2495fa
cancellation does not interfere with the transparent offset
and full-scale auto-calibration and the absolute accuracy
(full scale + offset + linearity + drift) is maintained even
with external RC networks.
Power-Up Sequence
The LTC2495 automatically enters an internal reset state
when the power supply voltage, VCC, drops below a
threshold of approximately 2.0V. This feature guarantees
the integrity of the conversion result and input channel
selection.
WhenVCCrisesabovethisthreshold,theconvertercreates
an internal power-on-reset (POR) signal with a duration
of approximately 4ms. The POR signal clears all internal
registers. The conversion immediately following a POR
cycle is performed on the input channels IN+ = CH0 and
IN– = CH1 with simultaneous 50Hz/60Hz rejection, 1x
output rate, and gain = 1. The first conversion following a
POR cycle is accurate within the specification of the device
if the power supply voltage is restored to (2.7V to 5.5V)
before the end of the POR interval. A new input channel,
rejection mode, speed mode, temperature selection or
gain can be programmed into the device during this first
data input/output cycle.
Reference Voltage Range
Thisconverteracceptsatrulydifferentialexternalreference
voltage.Theabsolute/commonmodevoltagerangeforthe
REF+ and REF– pins covers the entire operating range of
the device (GND to VCC). For correct converter operation,
VREF must be positive (REF+ > REF–).
The LTC2495 differential reference input range is 0.1V to
VCC. For the simplest operation, REF+ can be shorted to
VCC and REF– can be shorted to GND. The converter out-
put noise is determined by the thermal noise of the front
end circuits and, as such, its value in nanovolts is nearly
constant with reference voltage. A decrease in reference
voltage will not significantly improve the converter’s effec-
tive resolution. On the other hand, a decreased reference
will improve the converter’s overall INL performance.
Input Voltage Range
The analog inputs are truly differential with an absolute,
commonmoderangefortheCH0-CH15andCOMinputpins
extending from GND – 0.3V to VCC + 0.3V. Outside these
limits, the ESD protection devices begin to turn on and the
errorsduetoinputleakagecurrentincreaserapidly.Within
these limits, the LTC2495 converts the bipolar differential
input signal VIN = IN+ – IN– (where IN+ and IN– are the
selected input channels), from – FS = – 0.5 VREF/Gain
to + FS = 0.5 VREF/Gain where VREF = REF+ – REF–.
Outside this range, the converter indicates the overrange
or the underrange condition using distinct output codes
(see Table 1).
Signals applied to the input (CH0-CH15, COM) may extend
300mV below ground and above VCC. In order to limit
any fault current, resistors of up to 5k may be added in
series with the input. The effect of series resistance on
the converter accuracy can be evaluated from the curves
presentedintheInputCurrent/ReferenceCurrentsections.
In addition, series resistors will introduce a temperature
dependent error due to input leakage current. A 1nA input
leakage current will develop a 1ppm offset error on a 5k
resistor if VREF = 5V. This error has a very strong tem-
perature dependency.
MUXOUT/ADCIN
Theoutputsofthemultiplexer(MUXOUTP/MUXOUTN)and
the inputs to the ADC (ADCINP/ADCINN) can be used to
perform input signal conditioning on any of the selected
input channels or simply shorted together for direct
digitization. If an external amplifier is used, the LTC2495
automatically calibrates both the offset and drift of this
circuit and the Easy Drive sampling scheme enables a
wide variety of amplifiers to be used.
In order to achieve optimum performance, if an external
amplifier is not used, short these pins directly together
(ADCINP to MUXOUTP and ADCINN to MUXOUTN) and
minimize their capacitance to ground.
applicaTions inFormaTion
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2615IGN#TR | SERIAL INPUT LOADING, 9 us SETTLING TIME, 14-BIT DAC, PDSO16 |
| LTC2620CUFD#PBF | SERIAL INPUT LOADING, 7 us SETTLING TIME, 12-BIT DAC, PQCC20 |
| LTC2600CUFD#PBF | SERIAL INPUT LOADING, 10 us SETTLING TIME, 16-BIT DAC, PQCC20 |
| LTC2600CUFD#TRPBF | SERIAL INPUT LOADING, 10 us SETTLING TIME, 16-BIT DAC, PQCC20 |
| LTC2600IUFD#PBF | SERIAL INPUT LOADING, 10 us SETTLING TIME, 16-BIT DAC, PQCC20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2495IUHF#PBF | 功能描述:IC ADC 16BIT W/PGA 38-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2495IUHF#TRPBF | 功能描述:IC ADC 16BIT W/PGA 38-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2496CUHF#PBF | 功能描述:IC ADC 16BIT DELTA SIG 38-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2496CUHF#TRPBF | 功能描述:IC ADC 16BIT DELTA SIG 38-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2496IUHF#PBF | 功能描述:IC ADC 16BIT DELTA SIG 38-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
發布緊急采購，3分鐘左右您將得到回復。