- 您現在的位置：買賣IC網 > PDF目錄10353 > LTC2480IMS#PBF (Linear Technology)IC ADC 16BIT 10-MSOP PDF資料下載
參數資料
| 型號： | LTC2480IMS#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 13/42頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 16BIT 10-MSOP |
| 標準包裝： | 50 |
| 位數： | 16 |
| 采樣率（每秒）： | 7.5 |
| 數據接口： | MICROWIRE?，串行，SPI? |
| 轉換器數目： | 1 |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 2 個單端，雙極；1 個差分，雙極 |
| 配用： | DC798B-ND - BOARD DELTA SIGMA ADC LTC2480 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
LTC2480
0
2480fd
value with a temperature coefficient of 420/(27 + 273) =
1.40mV/°C (SLOPE), as shown in Figure 4. The internal
PTAT signal is used in a single-ended mode referenced
to device ground internally. The GAIN is automatically
set to one (independent of the values of GS0, GS1, GS2)
in order to preserve the PTAT property at the ADC output
code and avoid an out of range error. The 1x speed mode
with automatic offset calibration is automatically selected
for the internal PTAT signal measurement as well.
If the same VREF source is used during calibration and
temperature measurement, the actual value of the VREF
is not needed to measure the temperature as shown in
the calculation below:
T
R
V
SLOPE
R
T
C
SDO
REF
SDO
=
+
(
)
–
–
273
0
0 273 273
Reference Voltage Range
The LTC2480 external reference voltage range is 0.1V
to VCC. The converter output noise is determined by
the thermal noise of the front-end circuits, and as such,
its value in nanovolts is nearly constant with reference
voltage. Since the transition noise (600nV) is much less
than the quantization noise (VREF/217), a decrease in the
reference voltage will increase the converter resolution. A
reduced reference voltage will also improve the converter
performance when operated with an external conversion
clock (external fO signal) at substantially higher output
data rates (see the Output Data Rate section). VREF must
be ≥1.1V to use the internal temperature sensor.
The negative reference input to the converter is internally
tied to GND. GND (Pin 8) should be connected to a ground
plane through as short a trace as possible to minimize
voltage drop. The LTC2480 has an average operational
current of 160A and for 0.1Ω parasitic resistance, the
voltage drop of 16V causes a gain error of 3.2ppm for
VREF = 5V.
Input Voltage Range
The analog input is truly differential with an absolute/com-
mon mode range for the IN+ and IN– input pins extending
from GND – 0.3V to VCC + 0.3V. Outside these limits, the
ESD protection devices begin to turn on and the errors
due to input leakage current increase rapidly. Within these
limits, the LTC2480 converts the bipolar differential input
signal, VIN = IN+ – IN–, from –FS to +FS where FS = 0.5
VREF/GAIN. Outside this range, the converter indicates the
overrangeortheunderrangeconditionusingdistinctoutput
codes.Sincethedifferentialinputcurrentcancellationdoes
not rely on an on-chip buffer, current cancellation as well
as DC performance is maintained rail-to-rail.
applicaTions inForMaTion
TEMPERATURE (°C)
–60
V PTAT
(mV)
500
600
120
2480 F04
400
200
30
0
90
–30
60
300
VCC = 5V
IM = 1
FO = GND
SLOPE = 1.40mV/°C
Figure 4. Internal PTAT Signal vs Temperature
When using the internal temperature sensor, if the output
code is normalized to RSDO = VPTAT/VREF, the temperature
is calculated using the following formula:
T
R
V
SLOPE
T
R
V
SLOPE
K
SDO
REF
C
SDO
REF
=
°
–
in Kelvin
and
in C
273
where SLOPE is nominally 1.4mV/°C.
Since the PTAT signal can have an initial value variation
which results in errors in SLOPE, to achieve better tem-
perature measurements, a one-time calibration is needed
to adjust the SLOPE value. The converter output of the
PTAT signal, R0SDO, is measured at a known temperature
T0 (in °C) and the SLOPE is calculated as:
SLOPE
R
V
T
SDO
REF
=
+
0
0 273
This calibrated SLOPE can be used to calculate the tem-
perature.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9700BETB+T | IC AMP AUDIO 1.6W MONO D 10TDFN |
| VE-J4R-MX | CONVERTER MOD DC/DC 7.5V 75W |
| VE-J4N-MX | CONVERTER MOD DC/DC 18.5V 75W |
| MAX9700AETB+T | IC AMP AUDIO 1.6W MONO D 10TDFN |
| VE-J4M-MX | CONVERTER MOD DC/DC 10V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2481CDD#PBF | 功能描述:IC ADC 16BIT I2C 10-DFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2481CDD#TRPBF | 功能描述:IC ADC 16BIT I2C 10-DFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2481HDD#PBF | 功能描述:IC ADC 16BIT I2C 7.5SPS 10DFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2481HDD#TRPBF | 功能描述:IC ADC DELTA SIGMA 16BIT 10DFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2481IDD#PBF | 功能描述:IC ADC 16BIT I2C 10-DFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
發布緊急采購，3分鐘左右您將得到回復。