reset state when the power supply vol" />
參數資料
型號： LTC2431IMS#TRPBF
廠商： Linear Technology
文件頁數： 4/40頁
文件大?。?/td> 0K
描述： IC ADC 20BIT DIFFINPUT/REF10MSOP
標準包裝： 2,500
位數： 20
采樣率（每秒）： 7.5
數據接口： MICROWIRE?，串行，SPI?
轉換器數目： 2
功率耗散（最大）： 1mW
電壓電源： 單電源
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 10-TFSOP，10-MSOP（0.118"，3.00mm 寬）
供應商設備封裝： 10-MSOP
包裝： 帶卷 (TR)
輸入數目和類型： 1 個差分，雙極
配用： DC586A-ND - BOARD DELTA SIGMA ADC LTC2431
LTC2430/LTC2431
12
24301f
Power-Up Sequence
The LTC2430/LTC2431 automatically enter an internal
reset state when the power supply voltage VCC drops
below approximately 2V. This feature guarantees the
integrity of the conversion result and of the serial interface
mode selection. (See the 2-wire I/O sections in the Serial
Interface Timing Modes section.)
When the VCC voltage rises above this critical threshold,
the LTC2430 or LTC2431 creates an internal power-on-
reset (POR) signal with a duration of approximately 1ms.
The POR signal clears all internal registers. Following the
POR signal, the converter starts a normal conversion
cycle and follows the succession of states described
above. The first conversion result following POR is accu-
rate within the specifications of the device if the power
supply voltage is restored within the operating range
(2.7V to 5.5V) before the end of the POR time interval.
Reference Voltage Range
The LTC2430/LTC2431 accept a differential external refer-
ence voltage. The absolute/common mode voltage speci-
fication for the REF+ and REF– pins covers the entire range
from GND to VCC. For correct converter operation, the
REF+ pin must always be more positive than the REF– pin.
The LTC2430/LTC2431 can accept a differential reference
voltage from 0.1V to VCC. The converter (LTC2430 or
LTC2431) output noise is determined by the thermal noise
of the front-end circuits, and, as such, its value in micro-
volts is nearly constant with reference voltage. A decrease
in reference voltage will not significantly improve the
converter’s effective resolution. On the other hand, a re-
duced reference voltage will improve the converter’s over-
all INL performance. A reduced reference voltage will also
improve the converter performance when operated with
an external conversion clock (external FO signal) at sub-
stantially higher output data rates.
Input Voltage Range
The analog input is truly differential with an absolute/com-
mon mode range for the IN+ and IN– input pins extending
from GND – 0.3V to VCC + 0.3V. Outside these limits, the
ESD protection devices begin to turn on and the errors due
to input leakage current increase rapidly. Within these lim-
its, the LTC2430 or LTC2431 converts the bipolar differen-
tial input signal, VIN = IN+ – IN–, from – FS = –0.5 VREF
to +FS = 0.5 VREF where VREF = REF+ – REF –. Outside this
range the converter indicates the overrange or the
underrange condition using distinct output codes.
Input signals applied to IN+ and IN– pins may extend by
300mV below ground and above VCC. In order to limit any
fault current, resistors of up to 5k may be added in series
with the IN+ and IN– pins without affecting the performance
of the device. In the physical layout, it is important to main-
tain the parasitic capacitance of the connection between
these series resistors and the corresponding pins as low
as possible; therefore, the resistors should be located as
close as practical to the pins. In addition, series resistors
will introduce a temperature dependent offset error due to
the input leakage current. A 1nA input leakage current will
develop a 1ppm offset error on a 5k resistor if VREF = 5V.
This error has a very strong temperature dependency.
Output Data Format
The LTC2430/LTC2431 serial output data stream is 24 bits
long. The first 3 bits represent status information indicat-
ing the sign and conversion state. The next 21 bits are the
conversion result, MSB first. The third and fourth bits to-
gether are also used to indicate an underrange condition
(the differential input voltage is below – FS) or an overrange
condition (the differential input voltage is above + FS).
Bit 23 (first output bit) is the end of conversion (EOC)
indicator. This bit is available at the SDO pin during the
conversion and sleep states whenever the CS pin is LOW.
This bit is HIGH during the conversion and goes LOW
when the conversion is complete.
Bit 22 (second output bit) is a dummy bit (DMY) and is
always LOW.
Bit 21 (third output bit) is the conversion result sign indi-
cator (SIG). If VIN is >0, this bit is HIGH. If VIN is <0, this
bit is LOW.
Bit 20 (fourth output bit) is the most significant bit (MSB)
of the result. This bit in conjunction with Bit 21 also
provides the underrange or overrange indication. If both
Bit 21 and Bit 20 are HIGH, the differential input voltage is
APPLICATIO S I FOR ATIO
WU
UU
相關PDF資料
PDF描述
LTC2433-1IMS#TRPBF IC ADC DIFF 16BIT 3WIRE 10-MSOP
LTC2435CGN#TRPBF IC ADC DIFF I/REF 20BIT 16-SSOP
LTC2442IG#PBF IC ADC 24BIT 4CH 36-SSOP
LTC2446IUHF#TRPBF IC ADC 24BIT 8CH HI SPEED 38QFN
LTC2448IUHF#TRPBF IC ADC 24BIT HI SPEED 38QFN
相關代理商/技術參數
參數描述
LTC2433-1CMS 功能描述:IC ADC DIFF 16BIT 3WIRE 10-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494
LTC2433-1CMS#PBF 功能描述:IC ADC DIFF 16BIT 3WIRE 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
LTC2433-1CMS#TR 功能描述:IC CONV A/D 16BIT DIFF 10-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494
LTC2433-1CMS#TRPBF 功能描述:IC ADC DIFF 16BIT 3WIRE 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494
LTC2433-1CMSPBF 制造商:Linear Technology 功能描述:ADC,LTC2433 16bit diff D-S SPI MSOP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*