Lo" />
參數資料
型號： LTC2291IUP#PBF
廠商： Linear Technology
文件頁數： 15/28頁
文件大?。?/td> 0K
描述： IC ADC DUAL 12BIT 25MSPS 64QFN
標準包裝： 40
位數： 12
采樣率（每秒）： 25M
數據接口： 并聯
轉換器數目： 2
功率耗散（最大）： 180mW
電壓電源： 單電源
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 64-WFQFN 裸露焊盤
供應商設備封裝： 64-QFN（9x9）
包裝： 管件
輸入數目和類型： 2 個單端，雙極; 2 個差分, 雙極
產品目錄頁面： 1349 (CN2011-ZH PDF)
LTC2293/LTC2292/LTC2291
22
229321fa
ALVCH16373 CMOS latch. For full speed operation the
capacitive load should be kept under 10pF.
Lower OVDD voltages will also help reduce interference
from the digital outputs.
Data Format
Using the MODE pin, the LTC2293/LTC2292/LTC2291
parallel digital output can be selected for offset binary or
2’s complement format. Note that MODE controls both
Channel A and Channel B. Connecting MODE to GND or
1/3VDD selects offset binary output format. Connecting
MODE to 2/3VDD or VDD selects 2’s complement output
format. An external resistor divider can be used to set the
1/3VDD or 2/3VDD logic values. Table 2 shows the logic
states for the MODE pin.
APPLICATIO S I FOR ATIO
WU
U
Output Enable
The outputs may be disabled with the output enable pin, OE.
OE high disables all data outputs including OF. The data ac-
cess and bus relinquish times are too slow to allow the
outputs to be enabled and disabled during full speed op-
eration. The output Hi-Z state is intended for use during long
periods of inactivity. Channels A and B have independent
output enable pins (OEA, OEB).
Sleep and Nap Modes
The converter may be placed in shutdown or nap modes
to conserve power. Connecting SHDN to GND results in
normal operation. Connecting SHDN to VDD and OE to VDD
results in sleep mode, which powers down all circuitry
including the reference and typically dissipates 1mW. When
exiting sleep mode it will take milliseconds for the output
data to become valid because the reference capacitors have
to recharge and stabilize. Connecting SHDN to VDD and OE
to GND results in nap mode, which typically dissipates
30mW. In nap mode, the on-chip reference circuit is kept
on, so that recovery from nap mode is faster than that from
sleep mode, typically taking 100 clock cycles. In both sleep
and nap modes, all digital outputs are disabled and enter
the Hi-Z state.
Channels A and B have independent SHDN pins (SHDNA,
SHDNB). Channel A is controlled by SHDNA and OEA, and
Channel B is controlled by SHDNB and OEB. The nap, sleep
and output enable modes of the two channels are completely
independent, so it is possible to have one channel operat-
ing while the other channel is in nap or sleep mode.
Digital Output Multiplexer
The digital outputs of the LTC2293/LTC2292/LTC2291 can
be multiplexed onto a single data bus. The MUX pin is a
digital input that swaps the two data busses. If MUX is High,
Channel A comes out on DA0-DA11, OFA; Channel B comes
out on DB0-DB11, OFB. If MUX is Low, the output busses
are swapped and Channel A comes out on DB0-DB11, OFB;
Channel B comes out on DA0-DA11, OFA. To multiplex both
channels onto a single output bus, connect MUX, CLKA and
CLKB together (see the Timing Diagram for the multiplexed
mode). The multiplexed data is available on either data
bus—the unused data bus can be disabled with its OE pin.
Overflow Bit
When OF outputs a logic high the converter is either
overranged or underranged.
Output Driver Power
Separate output power and ground pins allow the output
drivers to be isolated from the analog circuitry. The power
supply for the digital output buffers, OVDD, should be tied
to the same power supply as for the logic being driven. For
example, if the converter is driving a DSP powered by a 1.8V
supply, then OVDD should be tied to that same 1.8V supply.
OVDD can be powered with any voltage from 500mV up to
3.6V. OGND can be powered with any voltage from GND up
to 1V and must be less than OVDD. The logic outputs will
swing between OGND and OVDD.
Table 2. MODE Pin Function
Clock Duty
MODE Pin
Output Format
Cycle Stabilizer
0
Offset Binary
Off
1/3VDD
Offset Binary
On
2/3VDD
2’s Complement
On
VDD
2’s Complement
Off
相關PDF資料
PDF描述
AD7892ARZ-3 IC ADC 12BIT LP 600KSPS 24SOIC
MS3100A20-6S CONN RCPT 3POS WALL MNT W/SCKT
LTC2280IUP#PBF IC ADC DUAL 10BIT 105MSPS 64-QFN
PT06A-14-5P CONN PLUG 5 POS STRAIGHT W/PINS
TAS5615DKDR IC AMP AUDIO 160W STER D 44HSSOP
相關代理商/技術參數
參數描述
LTC2291UP 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual 12-Bit, 65/40/25Msps Low Power 3V ADCs
LTC2292 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual 12-Bit, 65/40/25Msps Low Power 3V ADCs
LTC2292CUP 制造商:Linear Technology 功能描述:ADC Dual Pipelined 40Msps 12-bit Parallel 64-Pin QFN EP
LTC2292CUP#PBF 功能描述:IC ADC DUAL 12BIT 40MSPS 64QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6
LTC2292CUP#TRPBF 功能描述:IC ADC DUAL 12BIT 40MSPS 64QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*