參數資料
型號： LTC2259IUJ-14#TRPBF
廠商： Linear Technology
文件頁數： 19/34頁
文件大?。?/td> 0K
描述： IC ADC 14BIT 80MSPS 40-QFN
產品培訓模塊： LTC2262 - Ultra Low Power High Speed ADCs
標準包裝： 2,000
位數： 14
采樣率（每秒）： 80M
數據接口： 并聯，串行，SPI
轉換器數目： 1
功率耗散（最大）： 105mW
電壓電源： 單電源
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 40-WFQFN 裸露焊盤
供應商設備封裝： 40-QFN（6x6）
包裝： 帶卷 (TR)
輸入數目和類型： 1 個差分
配用： DC890B-ND - BOARD USB DATA COLLECTION
LTC2261-14
LTC2260-14/LTC2259-14
26
226114fc
For more information www.linear.com/LTC2261-14
applicaTions inForMaTion
Serial Programming Mode
To use the serial programming mode, PAR/SER should be
tied to ground. The CS, SCK, SDI and SDO pins become a
serialinterfacethatprogramtheA/Dmodecontrolregisters.
Data is written to a register with a 16-bit serial word. Data
can also be read back from a register to verify its contents.
Serial data transfer starts when CS is taken low. The data
on the SDI pin is latched at the first 16 rising edges of
SCK. Any SCK rising edges after the first 16 are ignored.
The data transfer ends when CS is taken high again.
The first bit of the 16-bit input word is the R/W bit. The
next seven bits are the address of the register (A6:A0).
The final eight bits are the register data (D7:D0).
If the R/W bit is low, the serial data (D7:D0) will be writ-
ten to the register set by the address bits (A6:A0). If the
R/W bit is high, data in the register set by the address bits
(A6:A0) will be read back on the SDO pin (see the timing
diagrams). During a read back command the register is
not updated and data on SDI is ignored.
The SDO pin is an open-drain output that pulls to ground
with a 200 impedance. If register data is read back
through SDO, an external 2k pull-up resistor is required. If
serial data is only written and read back is not needed, then
SDO can be left floating and no pull-up resistor is needed.
Table 3 shows a map of the mode control registers.
Software Reset
If serial programming is used, the mode control registers
shouldbeprogrammedassoonaspossibleafterthepower
supplies turn on and are stable. The first serial command
must be a software reset which will reset all register data
bits to logic 0. To perform a software reset, bit D7 in the
reset register is written with a logic 1. After the reset SPI
write command is complete, bit D7 is automatically set
back to zero.
Table 3. Serial Programming Mode Register Map
REGISTER A0: RESET REGISTER (ADDRESS 00h)
D7
D6
D5
D4
D3
D2
D1
D0
RESET
X
Bit 7
RESET
Software Reset Bit
0 = Not Used
1 = Software Reset. All Mode Control Registers are Reset to 00h. This Bit is Automatically Set Back to Zero at the End of the SPI Write
Command.
The Reset Register Is Write Only.
Bits 6-0
Unused, Don’t Care Bits.
REGISTER A1: POWER-DOWN REGISTER (ADDRESS 01h)
D7
D6
D5
D4
D3
D2
D1
D0
X
PWROFF1
PWROFF0
Bits 7-2
Unused, Don’t Care Bits.
Bits 1-0
PWROFF1:PWROFF0
Power Down Control Bits
00 = Normal Operation
01 = Nap Mode
10 = Not Used
11 = Sleep Mode
相關PDF資料
PDF描述
MS27466T15A35P CONN RCPT 37POS WALL MNT W/PINS
VE-BN4-IV-F2 CONVERTER MOD DC/DC 48V 150W
VE-BN3-IV-F4 CONVERTER MOD DC/DC 24V 150W
IDT72245LB25PFI8 IC FIFO 1024X18 SYNC 25NS 64QFP
MS3102E28-22SY CONN RCPT 6POS BOX MNT W/SCKT
相關代理商/技術參數
參數描述
LTC2259IUJ-16 制造商:LINER 制造商全稱:Linear Technology 功能描述:16-Bit, 80Msps Ultralow Power 1.8V ADC
LTC2259IUJ-16#PBF 制造商:Linear Technology 功能描述:ADC Single Pipelined 80Msps 16-bit Parallel/LVDS 40-Pin QFN EP 制造商:Linear Technology 功能描述:IC ADC 16BIT 80MSPS 40QFN
LTC2259IUJ-16#TRPBF 制造商:Linear Technology 功能描述:ADC Single Pipelined 80Msps 16-bit Parallel/LVDS 40-Pin QFN EP T/R 制造商:Linear Technology 功能描述:IC ADC 16BIT 80MSPS 40QFN
LTC2259IUJ-16PBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:16-Bit, 80Msps Ultralow Power 1.8V ADC
LTC2259IUJ-16TRPBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:16-Bit, 80Msps Ultralow Power 1.8V ADC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*