- 您現在的位置：買賣IC網 > PDF目錄39412 > LTC2165CUK#PBF (LINEAR TECHNOLOGY CORP) 1-CH 16-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC48 PDF資料下載
參數資料
| 型號： | LTC2165CUK#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | ADC |
| 英文描述： | 1-CH 16-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC48 |
| 封裝： | 7 X 7 MM, LEAD FREE, PLASTIC, MO-220WKKD-2, QFN-48 |
| 文件頁數： | 19/36頁 |
| 文件大?。?/td> | 663K |
| 代理商： | LTC2165CUK#PBF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
LTC2165/LTC2164/LTC2163
26
216543f
The digital output is decoded at the receiver by inverting
the odd bits (D1, D3, D5, D7, D9, D11, D13, D15.) The
alternate bit polarity mode is independent of the digital
output randomizer—either, both or neither function can
be on at the same time. The alternate bit polarity mode is
enabledbyseriallyprogrammingmodecontrolregisterA4.
Digital Output Test Patterns
To allow in-circuit testing of the digital interface to the
A/D, there are several test modes that force the A/D data
outputs (OF, D15 to D0) to known values:
All 1s: all outputs are 1
All 0s: all outputs are 0
Alternating: outputs change from all 1s to all 0s on
alternating samples.
Checkerboard: outputs change from
10101010101010101 to 01010101010101010
on alternating samples.
The digital output test patterns are enabled by serially
programming mode control register A4. When enabled,
the test patterns override all other formatting modes: 2’s
complement, randomizer, alternate bit polarity.
Output Disable
The digital outputs may be disabled by serially program-
ming mode control register A3. All digital outputs includ-
ing OF and CLKOUT are disabled. The high-impedance
disabled state is intended for in-circuit testing or long
periods of inactivity—it is too slow to multiplex a data
bus between multiple converters at full speed. When the
outputs are disabled the ADC should be put into either
sleep or nap mode.
Sleep and Nap Modes
The A/D may be placed in sleep or nap modes to conserve
power. In sleep mode the entire device is powered down,
resulting in 1mW power consumption. The amount of
time required to recover from sleep mode depends on
the size of the bypass capacitors on VREF, REFH, and
REFL. For the suggested values in Figure 8, the A/D will
stabilize after 2ms.
applicaTions inForMaTion
InnapmodetheA/Dcoreispowereddownwhiletheinternal
referencecircuitsstayactive,allowingfasterwake-upthan
from sleep mode. Recovering from nap mode requires at
least 100 clock cycles. If the application demands very
accurate DC settling then an additional 50s should be
allowed so the on-chip references can settle from the
slight temperature shift caused by the change in supply
current as the A/D leaves nap mode.
Sleep mode and nap mode are enabled by mode control
register A1 (serial programming mode), or by SDI and
SDO (parallel programming mode).
DEVICE PROGRAMMING MODES
The operating modes of the LTC2165/LTC2164/LTC2163
can be programmed by either a parallel interface or a
simple serial interface. The serial interface has more flex-
ibility and can program all available modes. The parallel
interface is more limited and can only program some of
the more commonly used modes.
Parallel Programming Mode
To use the parallel programming mode, PAR/SER should
be tied to VDD. The CS, SCK, SDI and SDO pins are binary
logic inputs that set certain operating modes. These pins
can be tied to VDD or ground, or driven by 1.8V, 2.5V, or
3.3V CMOS logic. When used as an input, SDO should be
driven through a 1k series resistor. Table 2 shows the
modes set by CS, SCK, SDI and SDO.
Table 2. Parallel Programming Mode Control Bits (PAR/SER = VDD)
PIN
DESCRIPTION
CS
Clock Duty Cycle Stabilizer Control Bit
0 = Clock Duty Cycle Stabilizer Off
1 = Clock Duty Cycle Stabilizer On
SCK
Digital Output Mode Control Bit
0 = Full Rate CMOS Output Mode
1 = Double Data Rate LVDS Output Mode
(3.5mA LVDS Current, Internal Termination Off)
SDI/SDO
Power-Down Control Bits
00 = Normal Operation
01 = Not Used
10 = Nap Mode
11 = Sleep Mode (Entire Device Powered Down)
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2165IUK#TRPBF | 1-CH 16-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC48 |
| LTC2163CUK#PBF | 1-CH 16-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC48 |
| LTC2165CUK#TRPBF | 1-CH 16-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC48 |
| LTC2163IUK#PBF | 1-CH 16-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC48 |
| LTC2170CUKG-12#TRPBF | 4-CH 12-BIT PROPRIETARY METHOD ADC, SERIAL ACCESS, PQCC52 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2165IUK#PBF | 制造商:Linear Technology 功能描述:IC ADC 16BIT PAR/SRL 125M 48QFN |
| LTC2165IUK#TRPBF | 制造商:Linear Technology 功能描述:IC ADC 16BIT PAR/SRL 125M 48QFN |
| LTC2170-12 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:12-Bit, 65Msps/40Msps/25Msps Low Power Quad ADCs |
| LTC2170-14 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Quad 14-Bit, 125Msps ADC with Integrated Drivers |
| LTC2170CUKG-12#PBF | 功能描述:IC ADC 12BIT SER/PAR 25M 52-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。