- 您現在的位置：買賣IC網 > PDF目錄11577 > LTC1955EUH#TR (Linear Technology)IC SMART CARD INTERFC DUAL 32QFN PDF資料下載
參數資料
| 型號： | LTC1955EUH#TR |
| 廠商： | Linear Technology |
| 文件頁數： | 20/22頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SMART CARD INTERFC DUAL 32QFN |
| 標準包裝： | 2,500 |
| 控制器類型： | 智能卡接口 |
| 接口： | 4 線串行 |
| 電源電壓： | 1.7 V ~ 5.5 V |
| 電流 - 電源： | 10µA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 32-QFN 裸露焊盤（5x5） |
| 包裝： | 帶卷 (TR) |
LTC1955
7
1955fd
For more information www.linear.com/LTC1955
pin FuncTions
SCLK: Input. The SCLK pin clocks the serial port. Each
new data bit is received on the rising edge of SCLK. SCLK
should be left high during idle times and should not be
clocked when LD is low.
LD: Input. The falling edge of this pin loads the current
state of the shift register into the command register.
Command changes to both smart card channels will be
updated on the falling edge of LD. The rising edge of LD
latches status information from the smart card channels
into the shift register for the next read/write cycle.
NC/NO: Input. This pin controls the activation level of the
PRES A/PRES B pins. When it is high (DVCC), the PRES
pins are active high. When it is low (GND), the PRES pins
are active low. When a ground side N.O. switch is used,
the NC/NO pin should be grounded. When a ground side
N.C. switch is used, the NC/NO pin should be connected
to DVCC.
Note: If an N.C. switch is used, a small current (several
microamperes) will flow through the switch whenever a
smartcardisnotpresent.Forultralowpowerconsumption
in shutdown, an N.O. switch is optimum.
PRES A/PRES B: Card Socket. The PRES A/PRES B pins
are used to detect the presence of the smart cards. They
can be connected to either normally open or normally
closed detection switches on the smart card acceptor’s
sockets.TheNC/NOpinshouldbesetappropriately.These
pins have a pull-up current source on-chip so no external
components are required.
C4A/C8A: Card Socket. These pins connect to the C4
and C8 pins of synchronous memory cards on smart
card socket A. The signal for these pins is unidirectional
and can only be sent to the card. Data for C4A and C8A
is transmitted via the DATA pin and may be selected
in place of I/OA via the serial port (see Table 4). When
either C4A or C8A is selected, it will follow the DATA
pin. When it is deselected, it will remain latched at its
current state.
I/O A/I/O B: Card Socket. The I/O A/I/O B pins connect to
the I/O pins of the respective smart card sockets. When
a smart card is selected, its I/O pin connects to the DATA
pin. When a smart card is deselected, its I/O A/I/O B pin
returns to the idle state (H).
RSTA/RSTB:CardSocket.Thesepinsshouldbeconnected
to the RST pins of the respective smart card sockets. The
RST A/RST B signals are derived from the RIN pin. When
a card is selected, its RST pin follows RIN. When a card
is deselected, the RST A/RST B pin for that channel holds
the current value on RIN.
CLK A/CLK B: Card Socket. The CLK A/CLK B pins should
be connected to the CLK pins of the respective smart card
sockets. The CLK A/CLK B signals can be derived from
either the SYNC input or the ASYNC input depending on
which type of card is being accessed. The card type is
selected via the serial port (see Tables 1 and 3).
VCCA, VCCB: Card Socket. The VCCA/VCCB pins should be
connected to the VCC pins of the respective smart card
sockets. The activation of a VCCA/VCCB pin is controlled by
the serial port (see Tables 1 and 2) and can be set to 0V,
1.8V, 3V or 5V. The voltage levels of the two card sockets
are controlled independently for maximum flexibility.
FAULT: Output. The FAULT pin can be used as an interrupt
to a microcontroller to indicate when a fault has occurred.
It is an open-drain output, which is logically equivalent to
D4 + D5 + D12 + D13. (See Table 1)
UNDERV: Input. The UNDERV pin provides security by
supplying a precision undervoltage threshold for ex-
ternal supply monitoring. An external resistive voltage
divider programs the desired undervoltage threshold.
Once UNDERV falls below 1.23V, the LTC1955 automati-
cally begins the deactivation sequence on any channel
that is active.
If external supply monitoring is not required, the UNDERV
pin should be connected to either SVBATT or DVCC.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-26B-CV-S | CONVERTER MOD DC/DC 95V 150W |
| LTC4267IGN#TRPBF | IC POE 802.3AF INTERFACE 16SSOP |
| LTC4267CGN#PBF | IC POE 802.3AF INTERFACE 16SSOP |
| LTC4267CDHC#TRPBF | IC POE 802.3AF INTERFACE 16-DFN |
| LTC4267CGN#TRPBF | IC POE 802.3AF INTERFACE 16SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1955IUH#PBF | 功能描述:IC SMART CARD INTERFACE DL 32QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND |
| LTC1955IUH#TRPBF | 功能描述:IC SMART CARD INTERFACE DL 32QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND |
| LTC1957-1EMS8 | 功能描述:IC RF PWR CONTRLLR SINGLE 8-MSOP RoHS:否 類別:RF/IF 和 RFID >> RF 電源控制器 IC 系列:- 標準包裝:3,000 系列:- RF 型:GSM 頻率:450MHz ~ 2GHz 特點:四頻帶 封裝/外殼:8-VFBGA 供應商設備封裝:8-MicroSMD（1.51x1.51） 包裝:帶卷 (TR) 其它名稱:LMV243BLX |
| LTC1957-1EMS8#PBF | 功能描述:IC RF PWR CONTRLLR SINGLE 8-MSOP RoHS:是 類別:RF/IF 和 RFID >> RF 電源控制器 IC 系列:- 標準包裝:3,000 系列:- RF 型:GSM 頻率:450MHz ~ 2GHz 特點:四頻帶 封裝/外殼:8-VFBGA 供應商設備封裝:8-MicroSMD（1.51x1.51） 包裝:帶卷 (TR) 其它名稱:LMV243BLX |
| LTC1957-1EMS8#TR | 功能描述:IC RF PWR CONTRLLR SINGLE 8-MSOP RoHS:否 類別:RF/IF 和 RFID >> RF 電源控制器 IC 系列:- 標準包裝:3,000 系列:- RF 型:GSM 頻率:450MHz ~ 2GHz 特點:四頻帶 封裝/外殼:8-VFBGA 供應商設備封裝:8-MicroSMD（1.51x1.51） 包裝:帶卷 (TR) 其它名稱:LMV243BLX |
發(fā)布緊急采購，3分鐘左右您將得到回復。