- 您現在的位置：買賣IC網 > PDF目錄296327 > LTC1751EMS8-5 Analog IC PDF資料下載
參數資料
| 型號： | LTC1751EMS8-5 |
| 英文描述： | Analog IC |
| 中文描述： | 模擬IC |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 178K |
| 代理商： | LTC1751EMS8-5 |
6
LTC1701/LTC1701B
APPLICATIO S I FOR ATIO
WU
U
Accepting larger values of
IL allows the use of low
inductances, but results in higher output voltage ripple
and greater core losses. A reasonable starting point for
setting ripple current is
IL = 0.4A.
The inductor value also has an effect on low current
operation. Lower inductor values (higher
IL) will cause
Burst Mode operation to begin at higher load currents,
which can cause a dip in efficiency in the upper range of
low current operation. In Burst Mode operation, lower
inductance values will cause the burst frequency to de-
crease.
Inductor Core Selection
Once the value for L is selected, the type of inductor must
be chosen. Basically, there are two kinds of losses in an
inductor —core and copper losses.
Core losses are dependent on the peak-to-peak ripple
current and core material. However, it is independent of
the physical size of the core. By increasing inductance, the
peak-to-peak inductor ripple current will decrease, there-
fore reducing core loss. Unfortunately, increased induc-
tance requires more turns of wire and, therefore, copper
losses will increase.
High efficiency converters generally cannot afford the core
loss found in low cost powdered iron cores, forcing the
use of more expensive ferrite, molypermalloy or Kool M
cores. Ferrite designs have very low core loss and are
preferred at high switching frequencies. Ferrite core ma-
terial saturates “hard,” which means that inductance col-
lapses abruptly when the peak design current is exceeded.
This results in an abrupt increase in inductor ripple current
and consequent output voltage ripple. Do not allow the
core to saturate!
Molypermalloy (from Magnetics, Inc.) is a very good, low
loss core material for toroids, but it is more expensive than
ferrite. A reasonable compromise from the same manu-
facturer is Kool M
core material. Toroids are very space
efficient, expecially when you can use several layers of
wire. Because they generally lack a bobbin, mounting is
more difficult. However, surface mount designs that do
not increase the height significantly are available
Catch Diode Selection
The diode D1 shown in Figure 1 conducts during the off-
time. It is important to adequately specify the diode peak
current and average power dissipation so as not to exceed
the diode ratings.
Losses in the catch diode depend on forward drop and
switching times. Therefore, Schottky diodes are a good
choice for low drop and fast switching times.
Since the catch diode carries the load current during the
off-time, the average diode current is dependent on the
switch duty cycle. At high input voltages, the diode con-
ducts most of the time. As VIN approaches VOUT, the diode
conducts only a small fraction of the time. The most
stressful condition for the diode is when the regulator
output is shorted to ground.
Under short-circuit conditions (VOUT = 0V), the diode
must safely handle ISC(PK) at close to 100% duty cycle.
Under normal load conditions, the average current con-
ducted by the diode is simply:
II
VV
DIODE avg
LOAD avg
IN
OUT
IN
D
()
=
+
Remember to keep lead lengths short and observe proper
grounding (see Board Layout Considerations) to avoid
ringing and increased dissipation.
The forward voltage drop allowed in the diode is calculated
from the maximum short-circuit current as:
V
P
I
VV
V
D
SC avg
IN
D
IN
≈
+
()
where PD is the allowable diode power dissipation and will
be determined by efficiency and/or thermal requirements
(see Efficiency Considerations).
Most LTC1701 circuits will be well served by either an
MBR0520L or an MBRM120L. An MBR0520L is a good
choice for IOUT(MAX) ≤ 500mA, as long as the output
doesn’t need to sustain a continuous short.
Kool M
is a registered trademark of Magnetics, Inc.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1757-1CMS8 | AMP POWER CONTROLLER |
| LTC1757-2CMS8 | Industrial Control IC |
| LTC1798CS8 | Voltage Reference |
| LTC1798CS8-2.5 | Voltage Reference |
| LTC1864AIS8 | A/D CONVERTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1751EMS8-5#PBF | 功能描述:IC REG SWITCHED CAP DBL 5V 8MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
| LTC1751EMS8-5#TR | 功能描述:IC REG SWITCHED CAP DBL 5V 8MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:1.24 V ~ 30 V 輸入電壓:1.5 V ~ 12 V PWM 型:電流模式，混合 頻率 - 開關:600kHz 電流 - 輸出:500mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:8-SOIC |
| LTC1751EMS8-5#TRPBF | 功能描述:IC REG SWITCHED CAP DBL 5V 8MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:1.24 V ~ 30 V 輸入電壓:1.5 V ~ 12 V PWM 型:電流模式，混合 頻率 - 開關:600kHz 電流 - 輸出:500mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:8-SOIC |
| LTC1753CG | 功能描述:IC SW REG CNTRLR PENT III 20SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| LTC1753CG#PBF | 功能描述:IC SW REG CNTRLR PENT III 20SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:2,000 系列:- 應用:控制器，DSP 輸入電壓:4.5 V ~ 25 V 輸出數:2 輸出電壓:最低可調至 1.2V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:30-TFSOP（0.173"，4.40mm 寬） 供應商設備封裝:30-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。