V 22 F TANTALUM VCC LTC1290 F06 0.1 F" />
參數資料
型號: LTC1290CISW#TR
廠商: Linear Technology
文件頁數: 11/32頁
文件大?。?/td> 0K
描述: IC DATA ACQ SYS 12BIT 5V 20SOIC
標準包裝: 1,000
類型: 數據采集系統(DAS),ADC
分辨率(位): 12 b
采樣率(每秒): 50k
數據接口: 串行,并聯
電壓電源: 雙 ±
電源電壓: ±5 V,5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 20-SOIC(0.295",7.50mm 寬)
供應商設備封裝: 20-SOIC
包裝: 帶卷 (TR)
19
LTC1290
1290fe
V
22
F
TANTALUM
VCC
LTC1290 F06
0.1
F
CERAMIC
DISK
ANALOG
GROUND
PLANE
1
10
20
U
S
A
O
PPLICATI
WU
U
I FOR ATIO
Figure 6. Example Ground Plane for the LTC1290
Figure 6 shows an example of an ideal ground plane design
for a two-sided board. Of course, this much ground plane
will not always be possible, but users should strive to get
as close to this ideal as possible.
2. Bypassing
For good performance, VCC must be free of noise and
ripple. Any changes in the VCC voltage with respect to
analog ground during a conversion cycle can induce
errors or noise in the output code. VCC noise and ripple can
be kept below 0.5mV by bypassing the VCC pin directly to
the analog ground plane with a 22
F tantalum capacitor
and leads as short as possible. The lead from the device to
the VCC supply should also be kept to a minimum and the
VCC supply should have a low output impedance such as
that obtained from a voltage regulator (e.g., LT1761).
Figures 7 and 8 show the effects of good and poor VCC
bypassing.
3. Analog Inputs
Because of the capacitive redistribution A/D conversion
techniques used, the analog inputs of the LTC1290 have
capacitive switching input current spikes. These current
Figure 7. Poor VCC Bypassing.
Noise and Ripple Can Cause A/D Errors
VERTICAL:
0.5mV/DIV
HORIZONTAL: 10
s/DIV
CS
VCC
Figure 8. Good VCC Bypassing Keeps
Noise and Ripple on VCC Below 1mV
HORIZONTAL: 10
s/DIV
VERTICAL:
0.5mV/DIV
spikes settle quickly and do not cause a problem. How-
ever, if large source resistances are used or if slow settling
op amps drive the inputs, care must be taken to insure that
the transients caused by the current spikes settle com-
pletely before the conversion begins.
Source Resistance
The analog inputs of the LTC1290 look like a 100pF
capacitor (CIN) in series with a 500 resistor (RON) as
shown in Figure 9. CIN gets switched between the selected
“+” and “–” inputs once during each conversion cycle. Large
external source resistors and capacitances will slow the
settling of the inputs. It is important that the overall RC time
constants be short enough to allow the analog inputs to
completely settle within the allowed time.
相關PDF資料
PDF描述
VE-B1F-IU-F2 CONVERTER MOD DC/DC 72V 200W
MS27473E16B6P CONN PLUG 6POS STRAIGHT W/PINS
V110A3V3M200BG CONVERTER MOD DC/DC 3.3V 200W
V110A3V3M200B CONVERTER MOD DC/DC 3.3V 200W
LTC1290DISW#TRPBF IC DATA ACQ SYS 12BIT 20-SOIC
相關代理商/技術參數
參數描述
LTC1290CMJ 制造商:Linear Technology 功能描述:ADC Single SAR 50ksps 12-bit Serial 20-Pin CDIP
LTC1290CMJ/883 制造商:Linear Technology 功能描述:ADC Single SAR 50ksps 12-bit Serial 20-Pin CDIP
LTC1290DCJ 制造商:Linear Technology 功能描述:ADC Single SAR 50ksps 12-bit Serial 20-Pin CDIP
LTC1290DCN 功能描述:IC DATA ACQ SYS 12BIT 20-DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統(DAS) 分辨率(位):16 b 采樣率(每秒):21.94k 數據接口:MICROWIRE?,QSPI?,串行,SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP(6x6) 包裝:托盤
LTC1290DCN#PBF 功能描述:IC DATA ACQ SYS 12BIT 20-DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Data Converter Basics 標準包裝:1 系列:- 類型:電機控制 分辨率(位):12 b 采樣率(每秒):1M 數據接口:串行,并聯 電壓電源:單電源 電源電壓:2.7 V ~ 3.6 V,4.5 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:100-TQFP 供應商設備封裝:100-TQFP(14x14) 包裝:剪切帶 (CT) 其它名稱:296-18373-1