- 您現在的位置：買賣IC網 > PDF目錄377727 > LTAEZ (Linear Integrated Systems) Differential Input 16-Bit No Latency DS ADC PDF資料下載
參數資料
| 型號： | LTAEZ |
| 廠商： | Linear Integrated Systems |
| 英文描述： | Differential Input 16-Bit No Latency DS ADC |
| 中文描述： | 差分輸入16位ADC的無延遲局副局長 |
| 文件頁數： | 12/28頁 |
| 文件大?。?/td> | 298K |
| 代理商： | LTAEZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LTC2433-1
12
24331fa
operation will not be disturbed if the change of conversion
clock source occurs during the sleep state or during the
data output state while the converter uses an external
serial clock. If the change occurs during the conversion
state, the result of the conversion in progress may be
outside specifications but the following conversions will
not be affected. If the change occurs during the data output
state and the converter is in the Internal SCK mode, the
serial clock duty cycle may be affected but the serial data
stream will remain valid.
Table 3 summarizes the duration of each state and the
achievable output data rate as a function of F
O
.
SERIAL INTERFACE PINS
The LTC2433-1 transmits the conversion results and
receives the start of conversion command through a
synchronous 3-wire interface. During the conversion and
sleep states, this interface can be used to assess the
converter status and during the data output state it is used
to read the conversion result.
Serial Clock Input/Output (SCK)
The serial clock signal present on SCK (Pin 9) is used to
synchronize the data transfer. Each bit of data is shifted out
the SDO pin on the falling edge of the serial clock.
In the Internal SCK mode of operation, the SCK pin is an
output and the LTC2433-1 creates its own serial clock by
dividing the internal conversion clock by 8. In the External
SCK mode of operation, the SCK pin is used as input. The
internal or external SCK mode is selected on power-up and
then reselected every time a HIGH-to-LOW transition is
detected at the CS pin. If SCK is HIGH or floating at power-
up or during this transition, the converter enters the inter-
nal SCK mode. If SCK is LOW at power-up or during this
transition, the converter enters the external SCK mode.
Serial Data Output (SDO)
The serial data output pin, SDO (Pin 8), provides the result
of the last conversion as a serial bit stream (MSB first)
during the data output state. In addition, the SDO pin is
used as an end of conversion indicator during the conver-
sion and sleep states.
When CS (Pin 7) is HIGH, the SDO driver is switched to a
high impedance state. This allows sharing the serial
interface with other devices. If CS is LOW during the
convert or sleep state, SDO will output EOC. If CS is LOW
during the conversion phase, the EOC bit appears HIGH on
the SDO pin. Once the conversion is complete, EOC goes
LOW.
Chip Select Input (CS)
The active LOW chip select, CS (Pin 7), is used to test the
conversion status and to enable the data output transfer as
described in the previous sections.
Table 3. LTC2433-1 State Duration
State
CONVERT
Operating Mode
Internal Oscillator
Duration
147ms, Output Data Rate
≤
6.8 Readings/s
F
O
= LOW
Simultaneous 50Hz/60Hz Rejection
F
O
= External Oscillator
with Frequency f
EOSC
kHz
(f
EOSC
/2560 Rejection)
External Oscillator
20510/f
EOSC
s, Output Data Rate
≤
f
EOSC
/20510 Readings/s
SLEEP
DATA OUTPUT
As Long As CS = HIGH Until CS = LOW and SCK
As Long As CS = LOW But Not Longer Than 1.09ms
(19 SCK cycles)
As Long As CS = LOW But Not Longer Than 152/f
EOSC
ms
(19 SCK cycles)
As Long As CS = LOW But Not Longer Than 19/f
SCK
ms
(19 SCK cycles)
Internal Serial Clock
F
O
= LOW
(Internal Oscillator)
F
O
= External Oscillator with
Frequency f
EOSC
kHz
External Serial Clock with
Frequency f
SCK
kHz
APPLICATIOU
W
U
U
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2433-1 | Differential Input 16-Bit No Latency DS ADC |
| LTC2433-1CMS | Differential Input 16-Bit No Latency DS ADC |
| LTC2433-1IMS | Differential Input 16-Bit No Latency DS ADC |
| LTC1043CS | Dual Precision Intrumentation Switched-Capacitor Building Block |
| LTC1043CN | Dual Precision Intrumentation Switched-Capacitor Building Block |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTAGL | 制造商:LINER 制造商全稱:Linear Technology 功能描述:100mA, Low Voltage, Very Low Dropout Linear Regulator |
| LT-ALTO350-C | 制造商:LED TEAM 功能描述:DRIVER 3CH DMX FOR RGB LED 350MA |
| LT-ALTO700-C | 制造商:LED TEAM 功能描述:LED DRIVER DC-DC CC 0.7A 制造商:LED TEAM 功能描述:LED DRIVER, DC-DC, CC, 0.7A 制造商:LED TEAM 功能描述:LED DRIVER, DC-DC, CC, 0.7A, Product Range:LED TEAM - ALTO700 Series, Input Volt 制造商:LED TEAM 功能描述:LED DRIVER, DC-DC, CC, 0.7A, Product Range:LED TEAM - ALTO700 Series, Input Voltage Min:24V, Input Voltage Max:32V, Output Current:700mA, Output Power Max:45W, DC / DC Converter Mounting:Panel, Dimming Control Type:PWM, Depth:22mm, , RoHS Compliant: Yes |
| LTALX | 制造商:Apex Tool Group 功能描述:TIP,BENT CHISEL,30 DEG,1.6MM,WP80 |
| L-TAPC64013BLLK3E-DB | 制造商:LSI Corporation 功能描述:HUGHES NETWORK KEY CUSTOMER |
發布緊急采購，3分鐘左右您將得到回復。