- 您現在的位置：買賣IC網 > Datasheet目錄41 > LT4254CGN (Linear Technology)IC CTRLR HOTSWAP POSVOLT 16SSOP Datasheet資料下載
參數資料
| 型號： | LT4254CGN |
| 廠商： | Linear Technology |
| 文件頁數： | 11/16頁 |
| 文件大?。?/td> | 232K |
| 描述： | IC CTRLR HOTSWAP POSVOLT 16SSOP |
| 標準包裝： | 100 |
| 類型： | 熱交換控制器 |
| 應用： | 通用 |
| 內部開關： | 無 |
| 電源電壓： | 10.8 V ~ 36 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-SSOP |
| 包裝： | 管件 |
| 產品目錄頁面： | 1341 (CN2011-ZH PDF) |
LT4254
11
4254fb
Layout Considerations section for important information
about board layout to minimize current limit threshold
error.
The LT4254 also features a variable overcurrent response
time. The time required for the part to regulate the GATE
pin voltage is a function of the voltage across the sense
resistor connected between the V
CC
pin and the SENSE pin.
This helps to eliminate sensitivity to current spikes and tran-
sients that might otherwise unnecessarily trigger a current
limit response and increase MOSFET dissipation. Figure 8
shows the response time as a function of the overdrive at
the SENSE pin.
TIMER
The TIMER pin provides a method for programming the
maximum time the part is allowed to operate in current
limit. When the current limit circuitry is not active, the
TIMER pin is pulled to GND by a 3礎 current source. When
the current limit circuitry becomes active, a 123礎 pull-up
current source is added to the TIMER pin and the voltage
will rise with a slope equal to 120礎/C
TIMER
as long as the
circuitry stays active. Once the desired maximum current
limit time is known, the capacitor value is:
C(nF) = 25.8 " t(ms)
Whenever the TIMER pin reaches 4.65V (typ), the internal
fault latch is set causing the GATE to be pulled low and the
TIMER pin to be discharged to GND by the 3礎 current
source. The part is not allowed to turn on again until the
voltage at the TIMER pin falls below 0.65V (typ).
The TIMER pin must never be pulled high by a low
impedance because whenever the TIMER pin voltage rises
above the upper threshold (typically 4.65V) the pin char-
acteristics change from a high impedance current source
to a low impedance. If the pin must be pulled high by a logic
signal, then a resistor must be put in series with the TIMER
pin to limit the current to approximately 100 microam-
peres. The resistance should be chosen as follows:
R
SERIES
= (V
LOGIC
4.65V)/100礎
Whenever the GATE pin is commanded off by any fault
condition, it is discharged with a high current, turning off
the external MOSFET. The waveform in Figure 9 shows how
the output latches off following a short-circuit. The drop
across the sense resistor is held at 12mV as the timer ramps
up. Since the output did not rise bringing FB above 2V and
the current is still 12mV/R5, the circuit latches off.
Automatic Restart
If the RETRY pin is floating, then the functionality is as
described in the previous section.
When the voltage at the TIMER pin ramps back down to
0.65V (typ), the LT4254 turns on again. If the short-circuit
condition at the output still exists, the cycle will repeat
itself indefinitely. The duty cycle under short-circuit con-
ditions is 3% which prevents Q1 from overheating.
Latch Off Operation
If the RETRY pin is grounded, the LT4254 will latch off
after a current fault. After the part latches off, it may be
APPLICATIO S I FOR ATIO
U
U
U
12mV
0V
2V
FB
4254 F07
50mV
V
CC
V
SENSE
50
100
150
200
4254 F08
12
10
8
6
4
2
V
CC
V
SENSE
(mV)
0
Figure 7. Current Limit Sense Voltage vs Feedback Pin Voltage
Figure 8. Response Time to Overcurrent
相關PDF資料 |
PDF描述 |
|---|---|
| LT4256-1IS8#TRPBF | IC CTRLR HOTSWAP HV LATCH 8SOIC |
| LTC1392IS8#TRPBF | IC DATA ACQ SYSTEM 10BIT 8-SOIC |
| LTC1421ISW-2.5#PBF | IC CONTROLLER HOT SWAP 24-SOIC |
| LTC1422CN8 | IC CONTROLLER HOT SWAP 8-DIP |
| LTC1642CGN#TRPBF | IC CONTROLLER HOTSWAP ADJ 16SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT4254CGN#PBF | 功能描述:IC CTRLR HOTSWAP POSVOLT 16SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LT4254CGN#TR | 功能描述:IC CTLR HOTSWAP POS 16-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LT4254CGN#TRPBF | 功能描述:IC CTRLR HOTSWAP POSVOLT 16SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LT4254IGN | 功能描述:IC CTLR HOTSWAP POS 16-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LT4254IGN#PBF | 功能描述:IC CTLR HOTSWAP POS 16-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。