參數資料
型號： LT4250LCN8
廠商： Linear Technology
文件頁數： 5/14頁
文件大小： 236K
描述： IC CONTRLR HOT SWAP NEG 48V 8DIP
標準包裝： 50
類型： 熱交換控制器
應用： 通用
內部開關： 無
電源電壓： -20 V ~ -80 V
工作溫度： 0°C ~ 70°C
安裝類型： 通孔
封裝/外殼： 8-DIP（0.300"，7.62mm）
供應商設備封裝： 8-PDIP
包裝： 管件
產品目錄頁面： 1341 (CN2011-ZH PDF)
LT4250L/LT4250H
5
4250lhfa
PIN FUNCTIONS
for this pin is 1.5約. Add an external capacitor to this pin
for additional filtering.
V
EE
 (Pin 4): Negative Supply Voltage Input. Connect to 
the lower potential of the power supply.
SENSE (Pin 5): Circuit Breaker Sense Pin. With a sense 
resistor placed in the supply path between V
EE
 and SENSE,
the overcurrent condition will pull down the GATE pin and
regulate the voltage across the resistor to be 50mV . If
the overcurrent condition exists for more than 500約 the
electronic circuit breaker will trip and turnoff the external
MOSFET .
If the current limit value is set to twice the normal operating
current, only 25mV is dropped across the sense resistor
during normal operation. To disable the current limit feature,
V
EE
 and SENSE can be shorted together.
GATE (Pin 6): Gate Drive Output for the External N-channel 
MOSFET . The GATE pin will go high when the following
start-up conditions are met: the UV pin is high, the OV pin
is low, (V
SENSE
  V
EE
) < 50mV and the V
DD
 pin is greater
than V
UVLOH
. The GATE pin is pulled high by a 45糀 cur-
rent source and pulled low with a 50mA current source.
During current limit the GATE pin is pulled low using a
100mA current source.
DRAIN (Pin 7): Analog Drain Sense Input. Connect this 
pin to the drain of the external N-channel MOSFET and
the V

 pin of the power module. When the DRAIN pin is
below V
DL
, the PWRGD/PWRGD pin will latch to indicate
the switch is on.
V
DD
 (Pin 8): Positive Supply Voltage Input. Connect this 
pin to the higher potential of the power supply inputs and
the V
+
 pin of the power module. An undervoltage lockout
circuit disables the chip until the V
DD
 pin is greater than
the 16V V
UVLOH
 threshold.
PWRGD/PWRGD (Pin 1): Power Good Output Pin. This pin 
will latch a power good indication when V
DRAIN
 is within
V
DL
 of V
EE
 and V
GATE
 is within V
GH
 of 擵
GATE
. This pin
can be connected directly to the enable pin of a power
module.
When the DRAIN pin of the LT4250L is above V
EE
 by more
than V
DL
 or V
GATE
 is more than V
GH
 from 擵
GATE
, the
PWRGD pin will be high impedance, allowing the pull-up
current of the modules enable pin to pull the pin high and
turn the module off. When V
DRAIN
 drops below V
DL
 and
V
GATE
 rises above V
GH
, the PWRGD pin sinks current to
V
EE
, pulling the enable pin low and turning on the module.
This condition is latched until the GATE pin is turned off
via the UV , OV , UVLO or the electronic circuit breaker.
When the DRAIN pin of the LT4250H is above V
EE
 by more
than V
DL
 or V
GATE
 is more than V
GH
 from 擵
GATE
, the
PWRGD pin will sink current to the DRAIN pin which pulls
the modules enable pin low, forcing it off. When V
DRAIN
 
drops below V
DL
 and V
GATE
 rises above V
GH
, the PWRGD
sink current is turned off, allowing the modules pull-up
current to pull the enable pin high and turn on the module.
This condition is latched until the GATE pin is turned off
via the UV , OV , UVLO or the electronic circuit breaker.
OV (Pin 2): Analog Overvoltage Input. When OV is pulled 
above the 1.255V threshold, an overvoltage condition is
detected and the GATE pin will be immediately pulled low.
The GATE pin will remain low until OV drops below the
1.235V threshold.
UV (Pin 3): Analog Undervoltage Input. When UV is pulled 
below the 1.125V threshold, an undervoltage condition
is detected and the GATE pin will be immediately pulled
low. The GATE pin will remain low until UV rises above
the 1.255 threshold.
The UV pin is also used to reset the electronic circuit
breaker. If the UV pin is cycled low and high following the
trip of the circuit breaker, the circuit breaker is reset and a
normal power-up sequence will occur. The response time
相關PDF資料
PDF描述
LT4254CGN IC CTRLR HOTSWAP POSVOLT 16SSOP
LT4256-1IS8#TRPBF IC CTRLR HOTSWAP HV LATCH 8SOIC
LTC1392IS8#TRPBF IC DATA ACQ SYSTEM 10BIT 8-SOIC
LTC1421ISW-2.5#PBF IC CONTROLLER HOT SWAP 24-SOIC
LTC1422CN8 IC CONTROLLER HOT SWAP 8-DIP
相關代理商/技術參數
參數描述
LT4250LCN8#PBF 功能描述:IC CONTRLR HOT SWAP NEG 48V 8DIP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件
LT4250LCS8 功能描述:IC CONTRLR HOTSWAP NEG 48V 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件
LT4250LCS8#PBF 功能描述:IC CONTRLR HOTSWAP NEG 48V 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件
LT4250LCS8#TR 功能描述:IC CONTRLR HOTSWAP NEG 48V 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件
LT4250LCS8#TRPBF 功能描述:IC CONTRLR HOTSWAP NEG 48V 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*