- 您現在的位置：買賣IC網 > PDF目錄44987 > LT3957EUHE#TRPBF (LINEAR TECHNOLOGY CORP) SWITCHING REGULATOR, PQCC36 PDF資料下載
參數資料
| 型號： | LT3957EUHE#TRPBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING REGULATOR, PQCC36 |
| 封裝： | 5 X 6 MM, LEAD FREE, PLASTIC, QFN-36 |
| 文件頁數： | 28/28頁 |
| 文件大小： | 359K |
| 代理商： | LT3957EUHE#TRPBF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁
LT3957
9
3957f
APPLICATIONS INFORMATION
Main Control Loop
The LT3957 uses a xed frequency, current mode control
scheme to provide excellent line and load regulation. Op-
eration can be best understood by referring to the Block
Diagram in Figure 1.
The start of each oscillator cycle sets the SR latch (SR1)
and turns on the internal power MOSFET switch M1 through
driver G2. The switch current ows through the internal
current sensing resistor RSENSE and generates a voltage
proportional to the switch current. This current sense
voltage VISENSE (amplied by A5) is added to a stabilizing
slope compensation ramp and the resulting sum (SLOPE)
is fed into the positive terminal of the PWM comparator A7.
When SLOPE exceeds the level at the negative input of A7
(VC pin), SR1 is reset, turning off the power switch. The
level at the negative input of A7 is set by the error amplier
A1 (or A2) and is an amplied version of the difference
between the feedback voltage (FBX pin) and the reference
voltage (1.6V or –0.8V, depending on the conguration).
In this manner, the error amplier sets the correct peak
switch current level to keep the output in regulation.
The LT3957 has a switch current limit function. The current
sense voltage is input to the current limit comparator A6.
If the SENSE2 pin voltage is higher than the sense current
limit threshold VSENSE(MAX) (48mV, typical), A6 will reset
SR1 and turn off M1 immediately.
The LT3957 is capable of generating either positive or
negative output voltage with a single FBX pin. It can be
congured as a boost, yback or SEPIC converter to gen-
erate positive output voltage, or as an inverting converter
to generate negative output voltage. When congured as
a SEPIC converter, as shown in Figure 1, the FBX pin is
pulled up to the internal bias voltage of 1.6V by a volt-
age divider (R1 and R2) connected from VOUT to SGND.
Comparator A2 becomes inactive and comparator A1
performs the inverting amplication from FBX to VC.
When the LT3957 is in an inverting conguration, the
FBX pin is pulled down to –0.8V by a voltage divider
connected from VOUT to SGND. Comparator A1 becomes
inactive and comparator A2 performs the noninverting
amplication from FBX to VC.
The LT3957 has overvoltage protection functions to
protect the converter from excessive output voltage
overshoot during start-up or recovery from a short-circuit
condition. An overvoltage comparator A11 (with 20mV
hysteresis) senses when the FBX pin voltage exceeds the
positive regulated voltage (1.6V) by 8% and provides a
reset pulse. Similarly, an overvoltage comparator A12
(with 10mV hysteresis) senses when the FBX pin voltage
exceeds the negative regulated voltage (–0.8V) by 11%
and provides a reset pulse. Both reset pulses are sent to
the main RS latch (SR1) through G6 and G5. The power
MOSFET switch M1 is actively held off for the duration of
an output overvoltage condition.
Programming Turn-On and Turn-Off Thresholds with
the EN/UVLO Pin
The EN/UVLO pin controls whether the LT3957 is enabled
or is in shutdown state. A micropower 1.22V reference,
a comparator A10 and a controllable current source IS1
allow the user to accurately program the supply voltage
at which the IC turns on and off. The falling value can be
accurately set by the resistor dividers R3 and R4. When
EN/UVLO is above 0.4V, and below the 1.22V threshold,
the small pull-down current source IS1 (typical 2μA) is
active.
The purpose of this current is to allow the user to program
the rising hysteresis. The Block Diagram of the comparator
and the external resistors is shown in Figure 1. The typical
falling threshold voltage and rising threshold voltage can
be calculated by the following equations:
VVIN,FALLING =1.22
(R3+R4)
R4
VVIN,RISING = 2A R3+ VIN,FALLING
For applications where the EN/UVLO pin is only used as
a logic input, the EN/UVLO pin can be connected directly
to the input voltage VIN for always-on operation.
相關PDF資料 |
PDF描述 |
|---|---|
| LT3957IUHE#PBF | SWITCHING REGULATOR, PQCC36 |
| LT3958IUHE#PBF | SWITCHING REGULATOR, PQCC36 |
| LT3958EUHE#PBF | SWITCHING REGULATOR, PQCC36 |
| LT3958EUHE#TRPBF | SWITCHING REGULATOR, PQCC36 |
| LT4180MPGN#PBF | POWER SUPPLY SUPPORT CKT, PDSO24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3957IUHE#PBF | 功能描述:IC REG MULTI CONFIG ADJ 36VQFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
| LT3957IUHE#TRPBF | 功能描述:IC REG MULTI CONFIG ADJ 36VQFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
| LT3957IUHEPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Boost, Flyback, SEPIC and Inverting Converter with 5A, 40V Switch |
| LT3957IUHETRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Boost, Flyback, SEPIC and Inverting Converter with 5A, 40V Switch |
| LT3958 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Monolithic High Voltage Isolated Flyback Converter No External Start-Up Resistor |
發布緊急采購，3分鐘左右您將得到回復。