- 您現在的位置：買賣IC網 > PDF目錄30767 > LT3653EDCB#TRPBF (LINEAR TECHNOLOGY CORP) 1.2 A BATTERY CHARGE CONTROLLER, 1650 kHz SWITCHING FREQ-MAX, PDSO8 PDF資料下載
參數資料
| 型號： | LT3653EDCB#TRPBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 1.2 A BATTERY CHARGE CONTROLLER, 1650 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | 2 X 3 MM, LEAD FREE, PLASTIC, DFN-8 |
| 文件頁數： | 12/12頁 |
| 文件大小： | 155K |
| 代理商： | LT3653EDCB#TRPBF |
LT3653
9
3653f
Battery Charger Operation
Connect the control node, VC pin, of the LT3653 to the
VC pin of the battery charger power path controller. The
VC node is internally clamped; however, take care not to
overdrive the pin. The LT3653 is internally compensated
with a pole zero combination on the output of the gm
amplier, G1. Check stability over the full input voltage
range, output load range and temperature.
Connect the HVOK node of the LT3653 to the high voltage
present pin of the charger. This is the WALL pin on the
LTC4098. The HVOK pin is capable of supplying up to 1mA
of drive current. When the HVOK pin is low the LT3653 is
not switching and the system output cannot be supported
by the LT3653 regulator. See the Typical Applications sec-
tion for different congurations.
PCB Layout
Proper operation and minimum EMI requires a careful
printed circuit board layout. Figure 1 shows the recom-
mended component placement with trace, ground plane
and via locations. Note that large, switched currents ow
in the LT3653’s VIN and SW pins, the catch diode (D1)
and the input capacitor (C1). Keep the loop formed by
these components as small as possible and tied to system
ground in only one place. Place these components, along
with the inductor and output capacitor, on the same side
of the circuit board, with their connections made on that
layer. Place a local, unbroken ground plane below these
components, and tie this ground plane to system ground
at one location, ideally at the ground terminal of the output
capacitor C2. Make the SW and BOOST nodes as short
as possible. Include vias near the exposed GND pad of
the LT3653 to help remove heat from the LT3653 to the
ground plane.
High Temperature Considerations
The die temperature of the LT3653 must not exceed
the maximum rating of 125°C. This is generally not a
concern unless the ambient temperature is above 85°C.
For higher temperatures, take care in the layout of the
circuit to ensure good heat sinking of the LT3653. Derate
the maximum load current as the ambient temperature
approaches 125°C. The die temperature is calculated by
multiplying the LT3653 power dissipation by the thermal
resistance from junction to ambient. Power dissipation
within the LT3653 is estimated by calculating the total
power loss from an efciency measurement and subtracting
the catch diode loss. Thermal resistance depends on the
layout of the circuit board, but 64°C/W is typical for the
(2mm
× 3mm) DFN (DCB) package.
Other Linear Technology Publications
Application Notes 19, 35 and 44 contain more detailed
descriptions and design information for Buck regulators
and other switching regulators. The LT1376 data sheet
has a more extensive discussion of output ripple, loop
compensation and stability testing.
APPLICATIONS INFORMATION
Figure 1. LT3653 PCB Layout
GND
VOUT
RILIM
C3
C1
C2
VIN
3
4
2
1
6
5
7
8
TO CHARGER:
HVOK
VC
3653 F01
相關PDF資料 |
PDF描述 |
|---|---|
| LT3684IMSE | 4 A SWITCHING REGULATOR, 3300 kHz SWITCHING FREQ-MAX, PDSO10 |
| LT3684EDD#TR | 4 A SWITCHING REGULATOR, 3300 kHz SWITCHING FREQ-MAX, PDSO10 |
| LT3694-1EUFD#PBF | 2.6 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PQCC28 |
| LT3694-1EUFD#TRPBF | 2.6 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PQCC28 |
| LT3694IUFD#TRPBF | 2.6 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PQCC28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3653IDCB#TRMPBF | 功能描述:IC REG BUCK ADJ 1.2A 8DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:升壓（升壓） 輸出類型:兩者兼有 輸出數:1 輸出電壓:5V，2 V ~ 16.5 V 輸入電壓:2 V ~ 16.5 V PWM 型:- 頻率 - 開關:45kHz 電流 - 輸出:50mA 同步整流器:無 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 包裝:管件 供應商設備封裝:8-PDIP |
| LT3653IDCB#TRPBF | 功能描述:IC REG BUCK ADJ 1.2A 8DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
| LT3653IDCB-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:1.2A, HV Input Regulator with Output Current Limit for Battery Charger Applications |
| LT3653IDCB-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:1.2A, HV Input Regulator with Output Current Limit for Battery Charger Applications |
| LT3663EDCB#TRMPBF | 功能描述:IC REG BUCK ADJ 1.2A 8DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
發布緊急采購，3分鐘左右您將得到回復。