- 您現在的位置：買賣IC網 > PDF目錄30767 > LT3653EDCB#TRPBF (LINEAR TECHNOLOGY CORP) 1.2 A BATTERY CHARGE CONTROLLER, 1650 kHz SWITCHING FREQ-MAX, PDSO8 PDF資料下載
參數資料
| 型號： | LT3653EDCB#TRPBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 1.2 A BATTERY CHARGE CONTROLLER, 1650 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | 2 X 3 MM, LEAD FREE, PLASTIC, DFN-8 |
| 文件頁數： | 11/12頁 |
| 文件大?。?/td> | 155K |
| 代理商： | LT3653EDCB#TRPBF |
LT3653
8
3653f
APPLICATIONS INFORMATION
Inductor Selection
A 4.7μH inductor is recommended for most LT3653 ap-
plications. This value provides a good tradeoff between
size and ripple current. The inductor’s RMS current rating
must be greater than the maximum load current and its
saturation current should be about 30% higher. The output
current limit circuit tightly controls the maximum average
inductor current therefore the inductor RMS current rating
does not have to be overrated to handle short-circuit or
overload conditions. For high efciency, keep the series
resistance (DCR) less than 0.1Ω. Output voltage ripple
can be reduced by using a higher value inductor. The cost
is a larger physical size and poorer transient response.
A lower value inductor has higher ripple currents but is
physically smaller or, for the same size, has lower DCR
usually resulting in higher efciency.
Catch Diode
The catch diode conducts current only during switch off
time. Average forward current in normal operation is
calculated from:
II
VV
V
D AVG
OUT
IN
OUT
IN
() =
where IOUT is the maximum output load current pro-
grammed by the ILIM resistor. Peak reverse voltage is
equal to the regulator input voltage. Use a Schottky diode
with a reverse voltage rating greater than the maximum
input voltage. The overvoltage protection feature in the
LT3653 keeps the switch off when VIN > 33V (typical),
allowing the use of a 40V rated Schottky, even when VIN
ranges up to 60V.
Input Capacitor
Bypass the input of the LT3653 circuit with a 4.7μF or higher
value ceramic capacitor of X7R or X5R type. Y5V types have
poor performance over temperature and applied voltage and
should not be used. If the input power source has high im-
pedance, or there is signicant inductance due to long wires
or cables, additional bulk capacitance may be necessary.
This can be provided with a low performance electrolytic
capacitor. Step-down regulators draw current from the
input supply in pulses with very fast rise and fall times.
The input capacitor is required to reduce the resulting volt-
age ripple at the LT3653 and to force this very high frequency
switching current into a tight local loop, minimizing EMI.
Place the capacitor in close proximity to the LT3653 and
the catch diode (see the PCB Layout section).
Output Capacitor
A 10μF or greater ceramic capacitor is required for low
output ripple and good transient response. Ceramic ca-
pacitors have very low equivalent series resistance (ESR)
and provide the best ripple performance. Use X5R or X7R
types and keep in mind that a ceramic capacitor biased
with VOUT has less than its nominal capacitance.
High performance electrolytic capacitors can be used for
the output capacitor. Low ESR is important, so choose
one that is intended for use in switching regulators. Keep
the ESR less than 0.1Ω.
ILIM Resistor
The LT3653 output current limit controls the maximum
current delivered from the LT3653 regulator. This allows
tighter control of the system power dissipation and also
protects the inductor and diode from overheating during
an overload or short-circuit condition. A resistor connected
from the ILIM pin to GND programs the output current
limit. Table 1 details the ILIM resistor values for specic
desired output current limits
Table 1. Output Current Limit vs RILIM Value
OUTPUT CURRENT LIMIT (A)
RILIM VALUE (kΩ)
0.4
121
0.6
66.5
0.8
45.3
1
33.2
1.2
27.4
Boost Capacitor Selection
The boost capacitor is calculated with the following for-
mula:
C
IV
VV
MHz
BOOST
OUT MAX
OUT
IN
=
()
..
()
01
30
15
Typically, a 0.1μF capacitor is used.
相關PDF資料 |
PDF描述 |
|---|---|
| LT3684IMSE | 4 A SWITCHING REGULATOR, 3300 kHz SWITCHING FREQ-MAX, PDSO10 |
| LT3684EDD#TR | 4 A SWITCHING REGULATOR, 3300 kHz SWITCHING FREQ-MAX, PDSO10 |
| LT3694-1EUFD#PBF | 2.6 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PQCC28 |
| LT3694-1EUFD#TRPBF | 2.6 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PQCC28 |
| LT3694IUFD#TRPBF | 2.6 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PQCC28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3653IDCB#TRMPBF | 功能描述:IC REG BUCK ADJ 1.2A 8DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:升壓（升壓） 輸出類型:兩者兼有 輸出數:1 輸出電壓:5V，2 V ~ 16.5 V 輸入電壓:2 V ~ 16.5 V PWM 型:- 頻率 - 開關:45kHz 電流 - 輸出:50mA 同步整流器:無 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 包裝:管件 供應商設備封裝:8-PDIP |
| LT3653IDCB#TRPBF | 功能描述:IC REG BUCK ADJ 1.2A 8DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
| LT3653IDCB-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:1.2A, HV Input Regulator with Output Current Limit for Battery Charger Applications |
| LT3653IDCB-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:1.2A, HV Input Regulator with Output Current Limit for Battery Charger Applications |
| LT3663EDCB#TRMPBF | 功能描述:IC REG BUCK ADJ 1.2A 8DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
發布緊急采購，3分鐘左右您將得到回復。