參數資料
型號： LT3581IDE#TRPBF
廠商： LINEAR TECHNOLOGY CORP
元件分類： 穩壓器
英文描述： SWITCHING REGULATOR, PDSO14
封裝： 4 X 3 MM, 0.75 MM HEIGHT, LEAD FREE, PLASTIC, MO-229WGED-3, DFN-14
文件頁數： 3/36頁
文件大?。?/td> 498K
代理商： LT3581IDE#TRPBF
LT3581
3581f
Sample Mode
Sample Mode is the mechanism used by the LT3581 to
aid in the detection of output shorts. It refers to a state of
the LT3581 where the master and slave power switches
(Q1 and Q2) are turned on for a minimum period of time
every clock cycle (or every few clock cycles in frequency
foldback) in order to “sample” the inductor current. If the
sampledcurrentthroughQ1exceedsthemasterswitchcur-
rent limit of 1.9A (min), the LT3581 triggers an overcurrent
fault internally (see Operation-Fault section for details).
Sample Mode is active when FB is out of regulation by
more than approximately 3.7% (45mV < FB < 1.17V).
Frequency Foldback
The frequency foldback circuit reduces the switching fre-
quency when 350mV < FB < 900mV (typical). This feature
lowers the minimum duty cycle that the part can achieve,
thus allowing better control of the inductor current dur-
ing start-up. When the FB voltage is pulled outside of this
range, the switching frequency returns to normal.
Note that the peak inductor current at start-up is a function
ofmanyvariablesincludingloadprofile,outputcapacitance,
target VOUT, VIN, switching frequency, etc. Test each and
everyapplication’sperformanceatstart-uptoensurethat
the peak inductor current does not exceed the minimum
fault current limit.
OPERATION – REGULATION
The following description of the LT3581’s operation as-
sumes that the FB voltage is close enough to its regulation
target so that the part is not in sample mode. Use the
Block Diagram as a reference when stepping through the
followingdescriptionoftheLT3581operatinginregulation.
At the start of each oscillator cycle, the SR latch (SR1) is
set, which turns on the power switches Q1 and Q2. The
collector current through the master switch, Q1, is ~1.3
times the collector current through the slave switch, Q2,
when the collectors of the two switches are tied together.
operaTion
Q1’semittercurrentflowsthroughacurrentsenseresistor
(RS) generating a voltage proportional to the total switch
current. This voltage (amplified by A4) is added to a sta-
bilizing ramp and the resulting sum is fed into the positive
terminal of the PWM comparator A3. When the voltage on
thepositiveinputofA3exceedsthevoltageonthenegative
input, the SR latch is reset, turning off the master and slave
power switches. The voltage on the negative input of A3
(VC pin) is set by A1 (or A2), which is simply an amplified
difference between the FB pin voltage and the reference
voltage (1.215V if the LT3581 is configured as a boost
converter, or 9mV if configured as an inverting converter).
In this manner, the error amplifier sets the correct peak
current level to maintain output regulation.
As long as the part is not in fault (see Operation – Fault
section) and the SS pin exceeds 1.8V, the LT3581 drives its
CLKOUT pin at the frequency set by the RT pin or the SYNC
pin. The CLKOUT pin can be used to synchronize other
compatible switching regulator ICs (including additional
LT3581s) with the LT3581. Additionally, CLKOUT’s duty
cycle varies linearly with the part’s junction temperature,
and may be used as a temperature monitor.
OPERATION – FAULT
The LT3581’s FAULT pin is an active low, bidirectional pin
that is pulled low to indicate a fault. Each of the following
events can trigger a fault in the LT3581:
A. FAULT1 events:
1. SW Overcurrent:
a. ISW1 > 1.9A (minimum)
b. (ISW1 + ISW2) > 3.3A (minimum)
2. VIN Voltage > 22V (minimum)
3. SW1 Voltage and/or SW2 Voltage > 42V
(minimum)
4. Die Temperature > 165°C
B. FAULT2 events:
1. Pulling the FAULT pin low externally
相關PDF資料
PDF描述
LT3581IMSE#TRPBF SWITCHING REGULATOR, PDSO16
LT3581IMSE#PBF SWITCHING REGULATOR, PDSO16
LT3581IDE#PBF SWITCHING REGULATOR, PDSO14
LT3682IDD#TRPBF SWITCHING REGULATOR, PDSO12
LT3682EDD#TRPBF SWITCHING REGULATOR, PDSO12
相關代理商/技術參數
參數描述
LT3581IMSE#PBF 功能描述:IC REG MULTI CONFIG ADJ 16MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤
LT3581IMSE#TRPBF 功能描述:IC REG MULTI CONFIG ADJ 16MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤
LT3581IMSE-PBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:3.3A Boost/Inverting DC/DC Converter with Fault Protection
LT3581IMSE-TRPBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:3.3A Boost/Inverting DC/DC Converter with Fault Protection
LT3582 制造商:LINER 制造商全稱:Linear Technology 功能描述:I2C Programmable Boost and Single Inductor Inverting DC/DC Converters with OTP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*