- 您現在的位置：買賣IC網 > PDF目錄377720 > LT1977 (Linear Technology Corporation) High Voltage 1.5A, 500kHz Step-Down Switching Regulator with 100uA Quiescent Current PDF資料下載
參數資料
| 型號： | LT1977 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | High Voltage 1.5A, 500kHz Step-Down Switching Regulator with 100uA Quiescent Current |
| 中文描述： | 高電壓，500kHz降壓1.5安培的電流型開關穩壓器的靜態電流為100uA |
| 文件頁數： | 17/24頁 |
| 文件大?。?/td> | 288K |
| 代理商： | LT1977 |
LT1977
17
1977f
APPLICATIOU
W
U
U
must weigh the importance of each specification in choos-
ing the best diode for the application.
The use of so-called “ultrafast” recovery diodes is gener-
ally not recommended. When operating in continuous
mode, the reverse recovery time exhibited by “ultrafast”
diodes will result in a slingshot type effect. The power
internal switch will ramp up V
IN
current into the diode in an
attempt to get it to recover. Then, when the diode has
finally turned off, some tens of nanoseconds later, the V
SW
node voltage ramps up at an extremely high dV/dt, per-
haps 5V to even 10V/ns! With real world lead inductances
the V
SW
node can easily overshoot the V
IN
rail. This can
result in poor RFI behavior and, if the overshoot is severe
enough, damage the IC itself.
BOOST PIN
For most applications the boost components are a 0.1
μ
F
capacitor and a MMSD914 diode. The anode is typically
connected to the regulated output voltage to generate a
voltage approximately V
OUT
above V
IN
to drive the output
stage (Figure 7a). However, the output stage discharges
the boost capacitor during the on time of the switch. The
output driver requires at least 2.5V of headroom through-
out this period to keep the switch fully saturated. If the
output voltage is less than 3.3V it is recommended that an
alternate boost supply is used. The boost diode can be
connected to the input (Figure 7b) but care must be taken
to prevent the boost voltage (V
BOOST
= V
IN
2) from
exceeding the BOOST pin absolute maximum rating. The
additional voltage across the switch driver also increases
power loss and reduces efficiency. If available, an inde-
pendent supply can be used to generate the required
BOOST voltage (Figure 7c). Tying BOOST to V
IN
or an
independent supply may reduce efficiency but it will re-
duce the minimum V
IN
required to start-up with light
loads. If the generated BOOST voltage dissipates too
much power at maximum load, the BOOST voltage the
LT1977 sees can be reduced by placing a Zener diode in
series with the BOOST diode (Figure 7a option).
A 0.1
μ
F boost capacitor is recommended for most appli-
cations. Almost any type of film or ceramic capacitor is
suitable but the ESR should be <1
to ensure it can be fully
recharged during the off time of the switch. The capacitor
value is derived from worst-case conditions of 1800ns on
time, 40mA boost current and 0.7V discharge ripple. The
boost capacitor value could be reduced under less de-
manding conditions but this will not improve circuit opera-
tion or efficiency. Under low input voltage and low load
conditions a higher value capacitor will reduce discharge
ripple and improve start-up operation.
SHUTDOWN FUNCTION AND UNDERVOLTAGE
LOCKOUT
The SHDN pin on the LT1977 controls the operation of the
IC. When the voltage on the SHDN pin is below the 1.2V
shutdown threshold the LT1977 is placed in a “zero”
supply current state. Driving the SHDN pin above the
shutdown threshold enables normal operation. The SHDN
pin has an internal sink current of 3
μ
A.
BOOST
LT1977
GND
V
BOOST
– V
= V
OUT
V
BOOST(MAX)
= V
IN
+ V
OUT
V
IN
V
OUT
OPTIONAL
(7a)
V
IN
SW
BOOST
LT1977
GND
V
BOOST
– V
= V
V
BOOST(MAX)
= V
DC
+ V
IN
V
IN
V
DC
D
SS
1977 F07
V
OUT
(7c)
V
IN
SW
BOOST
LT1977
GND
V
BOOST
– V
SW
= V
IN
V
BOOST(MAX)
= 2V
IN
V
IN
V
OUT
(7b)
V
IN
SW
Figure 7. BOOST Pin Configurations
相關PDF資料 |
PDF描述 |
|---|---|
| LT1977EFE | High Voltage 1.5A, 500kHz Step-Down Switching Regulator with 100uA Quiescent Current |
| LT1977IFE | High Voltage 1.5A, 500kHz Step-Down Switching Regulator with 100uA Quiescent Current |
| LT1990 | 250V Input Range G = 1, 10, Micropower, Difference Amplifier |
| LT1990ACS8 | 250V Input Range G = 1, 10, Micropower, Difference Amplifier |
| LT1990AIS8 | 250V Input Range G = 1, 10, Micropower, Difference Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1977EFE | 功能描述:IC REG BUCK ADJ 1.5A 16TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
| LT1977EFE#PBF | 功能描述:IC REG BUCK ADJ 1.5A 16TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
| LT1977EFE#TR | 功能描述:IC REG BUCK ADJ 1.5A 16TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LT1977EFE#TRPBF | 功能描述:IC REG BUCK ADJ 1.5A 16TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LT1977EFEPBF | 制造商:Linear Technology 功能描述:LT1977 adj PWM 1.5A SD dc-dc converter |
發布緊急采購，3分鐘左右您將得到回復。