- 您現在的位置：買賣IC網 > PDF目錄377719 > LT1962EMS8-5 (LINEAR TECHNOLOGY CORP) 300mA, Low Noise, Micropower LDO Regulators PDF資料下載
參數資料
| 型號： | LT1962EMS8-5 |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 300mA, Low Noise, Micropower LDO Regulators |
| 中文描述： | 5 V FIXED POSITIVE LDO REGULATOR, 0.43 V DROPOUT, PDSO8 |
| 封裝： | PLASTIC, MSOP-8 |
| 文件頁數： | 7/8頁 |
| 文件大?。?/td> | 138K |
| 代理商： | LT1962EMS8-5 |
7
LT1962 Series
The power dissipated by the device will be equal to:
I
OUT(MAX)
(V
IN(MAX)
– V
OUT
) + I
GND
(V
IN(MAX)
)
where,
I
OUT(MAX)
= 100mA
V
IN(MAX)
= 6V
I
GND
at (I
OUT
= 100mA, V
IN
= 6V) = 2mA
So,
P = 100mA(6V – 3.3V) + 2mA(6V) = 0.28W
The thermal resistance will be in the range of 110
°
C/W to
140
°
C/W depending on the copper area. So the junction
temperature rise above ambient will be approximately
equal to:
0.28W(125
°
C/W) = 35.3
°
C
The maximum junction temperature will then be equal to
the maximum junction temperature rise above ambient
plus the maximum ambient temperature or:
T
JMAX
= 50
°
C + 35.3
°
C = 85.3
°
C
Protection Features
The LT1962 regulators incorporate several protection
features which make them ideal for use in battery-powered
circuits. In addition to the normal protection features
associated with monolithic regulators, such as current
limiting and thermal limiting, the devices are protected
against reverse input voltages, reverse output voltages
and reverse voltages from output to input.
Current limit protection and thermal overload protection
are intended to protect the device against current overload
conditions at the output of the device. For normal opera-
tion, the junction temperature should not exceed 125
°
C.
The input of the device will withstand reverse voltages of
20V. Current flow into the device will be limited to less than
1mA (typically less than 100
μ
A) and no negative voltage
will appear at the output. The device will protect both itself
and the load. This provides protection against batteries
which can be plugged in backward.
The output of the LT1962 can be pulled below ground
without damaging the device. If the input is left open circuit
or grounded, the output can be pulled below ground by
20V. For fixed voltage versions, the output will act like a
large resistor, typically 500k or higher, limiting current
1. Output current multiplied by the input/output voltage
differential: (I
OUT
)(V
IN
– V
OUT
), and
2. GND pin current multiplied by the input voltage:
(I
GND
)(V
IN
).
The GND pin current can be estimated using specification
in the Electrical Characteristics table. Power dissipation
will be equal to the sum of the two components listed
above.
The LT1962 series regulators have internal thermal limit-
ing designed to protect the device during overload condi-
tions. For continuous normal conditions, the maximum
junction temperature rating of 125
°
C must not be
exceeded. It is important to give careful consideration to
all sources of thermal resistance from junction to ambient.
Additional heat sources mounted nearby must also be
considered.
For surface mount devices, heat sinking is accomplished
by using the heat spreading capabilities of the PC board
and its copper traces. Copper board stiffeners and plated
through-holes can also be used to spread the heat gener-
ated by power devices.
The following table lists thermal resistance for several
different board sizes and copper areas. All measurements
were taken in still air on 1/16" FR-4 board with one ounce
copper.
Table 1. Measured Thermal Resistance
COPPER AREA
TOPSIDE*
BACKSIDE
2500mm
2
2500mm
2
1000mm
2
2500mm
2
225mm
2
2500mm
2
100mm
2
2500mm
2
50mm
2
2500mm
2
THERMAL RESISTANCE
(JUNCTION-TO-AMBIENT)
110
°
C/W
115
°
C/W
120
°
C/W
130
°
C/W
140
°
C/W
BOARD AREA
2500mm
2
2500mm
2
2500mm
2
2500mm
2
2500mm
2
*Device is mounted on topside.
Calculating Junction Temperature
Example: Given an output voltage of 3.3V, an input voltage
range of 4V to 6V, an output current range of 0mA to
100mA and a maximum ambient temperature of 50
°
C,
what will the maximum junction temperature be
APPLICATIOU
W
U
U
相關PDF資料 |
PDF描述 |
|---|---|
| LT1962EMS8-3.3 | 300mA, Low Noise, Micropower LDO Regulators |
| LT1963AEST-1.5 | 1.5A, Low Noise, Fast Transient Response LDO Regulators |
| LT1963AES8-1.5 | 1.5A, Low Noise, Fast Transient Response LDO Regulators |
| LT1963AEST-3.3 | 1.5A, Low Noise, Fast Transient Response LDO Regulators |
| LT1963A-3.3 | 1.5A, Low Noise, Fast Transient Response LDO Regulators |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1962EMS8-5#PBF | 功能描述:IC REG LDO 5V .3A 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 產品培訓模塊:MIC5365/66 Ultra-small LDO Regulators 標準包裝:1 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:3V 輸入電壓:最高 5.5V 電壓 - 壓降（標準）:0.155V @ 150mA 穩壓器數量:1 電流 - 輸出:150mA 電流 - 限制（最?。?200mA 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:4-UDFN 裸露焊盤，4-TMLF? 供應商設備封裝:4-TMLF?（1x1） 包裝:Digi-Reel® 其它名稱:576-3192-6 |
| LT1962EMS8-5#TR | 功能描述:IC REG LDO 5V .3A 8-MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 產品培訓模塊:More Information on LDOs 標準包裝:50 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:3.3V 輸入電壓:最高 15V 電壓 - 壓降（標準）:1.1V @ 800mA 穩壓器數量:1 電流 - 輸出:800mA 電流 - 限制（最?。?800mA 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-263-4，D²Pak（3 引線+接片），TO-263AA 供應商設備封裝:D2PAK-3 包裝:管件 |
| LT1962EMS8-5#TRPBF | 功能描述:IC REG LDO 5V .3A 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 產品培訓模塊:More Information on LDOs 標準包裝:50 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:3.3V 輸入電壓:最高 15V 電壓 - 壓降（標準）:1.1V @ 800mA 穩壓器數量:1 電流 - 輸出:800mA 電流 - 限制（最?。?800mA 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-263-4，D²Pak（3 引線+接片），TO-263AA 供應商設備封裝:D2PAK-3 包裝:管件 |
| LT1962EMS8-5PBF | 制造商:Linear Technology 功能描述:LDO Regulator 5V 300mA Low Noise MSOP8 |
| LT1962EMS8PBF | 制造商:Linear Technology 功能描述: 制造商:Linear Technology 功能描述:LDO Regulator Adj. 300mA Low Noise MSOP8 |
發布緊急采購，3分鐘左右您將得到回復。