![](http://datasheet.mmic.net.cn/330000/LT1761ES5-2_datasheet_16427263/LT1761ES5-2_5.png)
5
LT1761 Series
OUTPUT CURRENT (mA)
500
450
400
350
300
250
200
150
100
50
0
D
1761 G01
0
10 20 30 40
50
60 70
80 90 100
T
J
≤
125
°
C
T
J
≤
25
°
C
= TEST POINTS
TEMPERATURE (
°
C)
–50
Q
μ
A
100
1761 G03
0
50
40
35
30
25
20
15
10
5
0
–25
25
75
125
V
IN
= 6V
R
L
=
∞
(250k FOR LT1761-BYP, -SD)
I
L
= 0 (5
μ
A FOR LT1761-BYP, -SD)
V
SHDN
= V
IN
V
SHDN
= 0V
TEMPERATURE (
°
C)
–50
O
100
1761 G06
0
50
1.84
1.83
1.82
1.81
1.80
1.79
1.78
1.77
1.76
–25
25
75
125
I
L
= 1mA
Guaranteed Dropout Voltage
Quiescent Current
LT1761-1.8
Output Voltage
Dropout Voltage
TEMPERATURE (
°
C)
–50
D
0
50
75
1761 G01.1
–25
25
100
125
I
L
= 100mA
I
L
= 50mA
I
L
= 10mA
I
L
= 1mA
500
450
400
350
300
250
200
150
100
50
0
OUTPUT CURRENT (mA)
500
450
400
350
300
250
200
150
100
50
0
D
1761 G00
0
10 20 30 40
50
60 70
80 90 100
T
J
= 125
°
C
T
J
= 25
°
C
Typical Dropout Voltage
Note 4:
Operating conditions are limited by maximum junction
temperature. The regulated output voltage specification will not apply for
all possible combinations of input voltage and output current. When
operating at maximum input voltage, the output current range must be
limited. When operating at maximum output current, the input voltage
range must be limited.
Note 5:
To satisfy requirements for minimum input voltage, the LT1761
(adjustable version) is tested and specified for these conditions with an
external resistor divider (two 250k resistors) for an output voltage of
2.44V. The external resistor divider will add a 5
μ
A DC load on the output.
Note 6:
Dropout voltage is the minimum input to output voltage differential
needed to maintain regulation at a specified output current. In dropout, the
output voltage will be equal to: V
IN
– V
DROPOUT
.
ELECTRICAL CHARACTERISTICS
Note 7:
GND pin current is tested with V
IN
= V
OUT(NOMINAL)
or V
IN
= 2.3V
(whichever is greater) and a current source load. This means the device is
tested while operating in its dropout region or at the minimum input
voltage specification. This is the worst-case GND pin current. The GND pin
current will decrease slightly at higher input voltages.
Note 8:
ADJ pin bias current flows into the ADJ pin.
Note 9:
SHDN pin current flows into the SHDN pin.
Note 10:
Reverse output current is tested with the IN pin grounded and the
OUT pin forced to the rated output voltage. This current flows into the OUT
pin and out the GND pin.
Note 11:
For the LT1761, LT1761-1.5, LT1761-1.8 and LT1761-2 dropout
voltage will be limited by the minimum input voltage specification under
some output voltage/load conditions. See the curve of Minimum Input
Voltage in the Typical Performance Characteristics.
TYPICAL PERFOR U
TEMPERATURE (
°
C)
–50
O
100
1761 G51
0
50
1.528
1.521
1.514
1.507
1.500
1.493
1.486
1.479
1.472
–25
25
75
125
I
L
= 1mA
LT1761-1.5
Output Voltage